Stimmen - 4, Durchschnittliche Bewertung: 3.8
(
)
)
|
Anleitung Zusammenfassung
Homeowner: Keep Installation Instructions for future reference. Save Installation Instructions for local electrical inspector's use. Quick Reference Table of Contents: Pages Before you start Electrical requirements Product dimensions Venting requirements Installation steps Use and Care Information Warranty Requesting Assistance or Service 2 2 3 3 4 -7 7 -8 8 9- 10 Part No. 626890B/8284957 Rev. A Piece N° 626890B/8284957 Rev. A Before you start... Your safety and the safety of others is very important. We have provided many important safety messages in this manual and on your appliance. Always read and Your safety and the safety of others is very important. We have provided many important safety messages in this manual and on your appliance. Always read and This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” obey all safety messages. or “WARNING”. These words mean: DANGER You can be killed or seriously injured if you don’t immediately follow 2 Proper installation is your responsibility. Make sure you have everything necessary for correct installation. It is the responsibility of the installer to comply with the clearances specified. Check the location where the range hood will be installed. The location should be away from strong draft areas, such as windows, doors, and strong heating vents. Mobile home installation The installation of this range hood must conform to the Manufactured Home Construction Safety Standards, Title 24 CFR, Part 328 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD, Part 280) or when such standard is not applicable, the Standard for Manufactured Home Installation 1982 (Manufactured Home Sites, Communities and Setups) ANSI A225.1/NFPA 501A*, or latest edition, or with local codes. Important: Observe all governing codes and ordinances. You can be killed or seriously injured if you don’t follow instructions. WARNING All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed. instructions. WARNING — TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable Codes and Standards, including Fire Rated Construction. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent back drafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society of Heating Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities. Ducted fans must always be vented to the outdoors. WARNING — To reduce the risk of fire, use only metal ductwork. This unit must be grounded. This hood is factory set for vented installations. For non-vented installations, purchase 30" (76.2 cm) Filter Kit No. 4396291 or 36" (91.4 cm) Filter Kit No. 4396292 from your dealer. Tools and materials needed for installation: • compass or 8" (20.3 cm) circle template • flat blade screwdriver • Phillips screwdriver • pliers • metal snips • drill • 1-1/4" (3.0 cm) drill bit • pencil • ruler • keyhole saw • saber saw • duct tape • 7" (17.8 cm) round damper if using 7" (17.8 cm) round vent system Electrical requirements Important: Observe all governing codes and ordinances. It is the customer’s responsibility: •To contact a qualified electrical installer. •To assure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70 — latest edition*, or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No.0-M91 - latest edition** and all local codes and ordinances. A separate ground wire must be used. It is recommended that a qualified electrician determine that the ground path is adequate. A 120-volt, 60-Hz, AC-only, fused electrical system is required. A separate 15-amp circuit is recommended. Do not ground to a gas pipe. Check with a qualified electrician if you are not sure range hood is properly grounded. Do not have a fuse in the neutral or ground circuit. IMPORTANT: Save Installation Instructions for electrical inspector’s use. The range hood must be connected with copper wire only. The range hood should be connected directly to the fused disconnect (or circuit breaker) box through flexible armored or nonmetallic sheathed copper cable. A U.L.- or C.S.A.-listed strain relief must be provided at each end of the power supply cable. Wire sizes (COPPER WIRE ONLY) and connections must conform with the rating of the appliance as s...
Dieses Handbuch ist für folgende Modelle:Ventilatoren - GZ5736 (278.28 kb)