Humid air is circulated throughout the home by the central heating system. All Bryant humidifiers are equipped with a humidistat to maintain the desired humidity level. Access to the media pad in the humidifier is convenient and tools are not required, allowing easy pad replacement. The fan-powered humidifiers, Model 913B and 913C, are designed for simple installation on supply ductwork, without a bypass duct required. Humidity is achieved by drawing heated supply air through a wet media pad, b

An observation window allows for convenient visual maintenance checks. Form No. PDS 912D.56.3B SPECIFICATIONS MODEL 912E 912D 913B 913C 914A ARI CAPACITY* Gallons/Day @ 140° (Lbs/hr) 17 (5.9) 18(6.3) 25 (8.7) 16(5.9) 19(6.6) Gallons/Day @ 120° (Lbs/hr) 12.8 (4.4) 13.5(4.7) 18.8 (6.5) 12.8 (4.5) 14.3(5.0) TYPE Airflow Bypass | Fan Bypass Waterflow Drain Through No drain GENERAL Evaporator Pad-Replacement L2-02623-2 I L2-02623-1 | L2-02623-3 L2-02950-1 Material

wc. t Single pole, single throw. ■ OPTIONAL WATER VALVE MOUNTING FRONT ACCESS COVER- Model 913B A96481 Model 913C Model 912D A96483 A96484 Model 914A Model 912E A96485 —3— RECOMMENDED RELATIVE HUMIDITY BY OUTDOOR TEMPERATURE INDOOR RELATIVE HUMIDITY LIMIT FOR NO WINDOW CONDENSATION (Indoor Air at 74°F Dry Bulb) OUTDOOR TEMPERATURE (°F) SINGLE PANE WINDOWS (%) DOUBLE PANE WINDOWS (%) 40 39 59 30 29 50 20 21 43 10 15 36 0 10 30 -10 7 26 -20 5 21 -30 3 17 OUTDOOR TEMP (°F) O

WC) EVAPORATION RATE VS STATIC & AIR TEMP (°F) GALLONS/DAY 913B 912D 912E 914A 913C 31.5 29.8 33.3 27.0 25.5 28.5 31.3 22.5 21.3 23.8 21.3 25 ,18 17 19 17 18.8 13.5 12.8 14.3 12.8 12.5 9.0 8.5 9.5 8.5 6.3 4.5 4.3 4.8 4.3 , 0 0 0 0 0 0.10 0.20 0.30 0.40 0.50 0.60 BYPASS DIFFERENTIAL STATIC IN. WC + FAN UNIT CAPACITY VARIES ONLY W/AIR TEMP. AT 0.20 STATIC POINT NOTE: DUCT STATIC HAS NO EFFECT ON 913B t RATING POINT ADDITIONAL EVAPORATION RATE USING HOT WATER GALLONS/DAY 913B 912D 9

CAUTION: Minimum duct size for mounting the humidifier is 8" x 1M-TT. Determine the most convenient side of duct for installation and maintenance. Lay out and cut a 7%" x 14-” hole on the bottom of the duct from the mounting side. On the mounting side of the duct, lay out a 7%TT wide by 7" high hole. See Figure 1. Install ,TZn bars on the 14-" sides. Slide the humidifier tray into the "Z" bars until the front flange is 3" from the duct side. Position the inspection plate on the humidifier tray

REFRESHING MOISTURE . . . AS NATURE INTENDED Congratulations on your excellent choice and sound investment in this addition to your home comfort system. Your humidifier represents both the latest in engineering development and the culmination of many years of experience from one of the most reputable manufacturers of comfort systems. Your new unit is among the most energy- efficient and reliable home humidifiers available today. To assure its dependability, spend a few minutes now with this book

7— Model HUMBBLFP1025-A- INLET CABINETRECTIFIER SOLENOID VALVE DISTRIBUTOR PAN EVAPORATOR PAD DUCT HOUSING SIDE ACCESS DOOR DRAIN Fig. 8— Model HUMBBSBP2017-A- CABINET FRONT COVER SCREWS (4) PAD ASSEMBLY SIDE ACCESS DOOR Fig. 9— Model HUMBBSFP1016-A- 4. Turn off the furnace. When the blower stops, look into the humidifier to make sure the water is not flowing into the unit. 5. Replace the cover assembly and fasten securely. 6. Now, turn the furnace on and set the thermostat for desired room temp

However, before performing any maintenance, consider these important safety precautions: • DISCONNECT ALL ELECTRICAL POWER TO THE HUMIDIFIER AND FURNACE BEFORE PERFORMING ANY SERVICE OR MAINTENANCE TO AVOID PERSONAL INJURY. BEARING RETAINER CABINET PAD PAN Fig. 10— Model HUMBBWTR2019-A- NOTE: THERE MAY BE MORE THAN 1 ELECTRICAL DISCONNECT SWITCH. • ALTHOUGH SPECIAL CARE HAS BEEN TAKEN TO MINIMIZE SHARP EDGES IN THE CONSTRUCTION OF YOUR HUMIDIFIER, BE EXTREMELY CAREFUL WHEN HANDLING PARTS OR REAC

The typical process of humidification begins when water flows through the humidifier valve and soaks the large evaporator pad. Hot, dry air from the furnace passes through the pad and absorbs the water. Then, this moisture-laden air is distributed throughout the house via the ductwork. See Fig. 1, 2, and 3. Fig. 1 Fig. 2 Fig. 3 EVAPORATOR PAD HUMIDIFIED AIR DRY AIR DRAIN DRY AIR HUMIDIFIED AIR TYPICAL INSTALLATIONS OPERATING YOUR HUMIDIFIER Your new humidifier is designed to operate as part of y

In areas where hard water and high mineral content are prevalent, more frequent cleaning and servicing may be required. At minimum, the humidifier will need to be cleaned at the beginning of every heating season. CLEANING PROCEDURES Models HUMBBLBP, HUMBBSBP, HUMBBLFP, and HUMBBSFP 1. Turn off all electrical power to the humidifier and furnace or fan coil. 2. Turn off the humidifier’s water supply. (See Fig. 4.) 3. Disassemble the humidifier. • To disassemble a Model HUMBBSBP humidifier, gently