Login:
heruntergeladen wurde: 1   Dateigröße: 4 kb   Hersteller: Life Fitness  
Kategorie: Kraftstationen

heruntergeladen wurde: 0   Dateigröße: 4 kb   Hersteller: Life Fitness  
Kategorie: Kraftstationen

heruntergeladen wurde: 25   Dateigröße: 4 kb   Hersteller: Life Fitness  
Kategorie: Kraftstationen

heruntergeladen wurde: 2   Dateigröße: 4 kb   Hersteller: Life Fitness  
Kategorie: Kraftstationen

heruntergeladen wurde: 6   Dateigröße: 14 kb   Hersteller: Life Fitness  
Kategorie: Kraftstationen
@name

Reinstall the new NORPRENE HOSE. Step 8 Reverse Steps 1 through 6 to return all parts to their proper positions taking special note to unkink the WAX CONTAINER HOSE prior to rejoining the FRONT and REAR FRAME ASSEMBLIES. NOTE: THIS IS NORMALLY AN OPPORTUNE TIME TO INSPECT THE WAX SPRAY NOZZLE. BETWEEN THE BOTTOM OF THE FRAME AND THE STRIDING BELT. PRESS THE SPRAY NOZZLE IN AND TWIST IT 1/4 TURN TO REMOVE. CLEAN OR REPLACE THE SPRAY NOZZLE AS DEEMED NECESSARY AND COMPLETE GENERAL CLEANING OF T

heruntergeladen wurde: 0   Dateigröße: 25 kb   Hersteller: Life Fitness  
Kategorie: Kraftstationen
@name

885 OLYMPIC ADAPTOR USER’S GUIDE WARNING: Read and follow all directions for each step to insure proper assembly of this product. CLASS H 1 Version: 885108 PART # 7303501 Revision: 06/18/02 REV. A TABLE OF CONTENTS Safety Statement.............2 General Maintenance.......4 General Notes..................3 Warranty Statement..........5 Assembly Instructions.....3 Product Services..............6 Insert-Registration Card IMPORTANT SAFETY INFORMATION THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE TH

heruntergeladen wurde: 9   Dateigröße: 26 kb   Hersteller: Life Fitness  
Kategorie: Kraftstationen
@name

Proceed with the following steps to facilitate proper installation. 1. Turn the unit power OFF at the switch, then unplug the line cord at the wall outlet. 2. Remove the motor cover and front cover. 3. Remove the motror controller mounting screws and slide the motor controller back to gain access to the wax lift board mounting screws and electrical connectors. 4. Disconnect all connectors from the Wax Lift Board. 5. Remove three phillips mounting screws from the PCB and remove. 6. Install

heruntergeladen wurde: 5   Dateigröße: 31 kb   Hersteller: Life Fitness  
Kategorie: Kraftstationen
@name

Install the Monocolumn Pad Kit Tools required: Phillips screwdriver, Socket set Step 1 Turn the power OFF at the ON/OFF switch and then unplug the unit from the electrical outlet. Step 2 Using a Phillips screwdriver, remove the two SCREWS securing the sides of the VENT COVER to the MOTOR COVER. Step 3 Grasp the VENT COVER in the center and pull away from the MOTOR COVER to disengage the two snap down CLIPS located on the inside, center of the VENT COVER. Step 4 Using a Phillips screwdri

heruntergeladen wurde: 1   Dateigröße: 32 kb   Hersteller: Life Fitness  
Kategorie: Kraftstationen

heruntergeladen wurde: 1   Dateigröße: 32 kb   Hersteller: Life Fitness  
Kategorie: Kraftstationen
@name

Align the TRANSFORMER LINE CORD with the CABLE TIE CLAMP leaving a small loop in the cord at the TRANSFORMER PLUG. Guide a REUSABLE CABLE TIE through the the CABLE TIE CLAMP and around the TRANSFORMER LINE CORD (Detail ‘C'). Tighten the CABLE TIE CLAMP around the TRANSFORMER LINE CORD. NOTE: DO NOT TRIM CABLE TIES Step 4 Apply the two reusable cable ties to combine the TRANSFORMER LINE CORD and the PC COMMUNICATIONS CABLE as shown in Figure A. Route the combined cables over the top of the fro





Kategorien