Light bulbs should be 12V 20W maximum. 5. Using a cloth, hold the new light bulb and push securely into light socket. 6. Return halogen light glass cover to the housing. . 7. Turn range hood ON to test for operation. 20 SPECIFICATIONS MODEL / SIZE CH7930SQB / 30” CH7936SQB / 36" CH7942SQB / 42" CH7948SQB / 48" COLOR Commercial Grade Stainless Steel CONSUMPTION / AMPERE 30” – 232W / 2.21A 36” – 232W / 2.21A 42” – 253W / 2.38A 48” – 258W / 2.41A NUMBER OF MOTORS 2 DESIGN 18-Gauge Seamless / Satin

- Try to avoid as many transitions, elbows, and long run as possible. This may reduce the performance of the hood. - Temporarily wire the hood to test for proper operation before installing. - Peel protective film off the hood (if any). - For installing under the cabinet with recessed bottom, attach 4-inch wide wood filler strips (not included) on each side. Refer to Figure 7. - Measure and create access opening for electrical wires under the cabinet or access opening for the electrical wires at

BEFORE CONNECTING WIRES, SWITCH POWER OFF AT SERVICE PANEL AND LOCK SERVICE PANEL TO PREVENT POWER FROM BEING SWITCHED ON ACCIDENTALLY. Connect the electrical wires. -Connect three wires (black, white and green) to house wires and cap with wire connectors. Connect according to color: black to black, white to white, and green to green. -If necessary to hide the electrical wire connections, push wires back into the wiring box. Access the wire connections underneath the hood. Make sure wires do not

Mark the position of the duct cover-mounting bracket. Use reference E from Table 2 and measurements on Page 22-23. Attach and secure duct cover-mounting bracket with two screws (not provided). Refer to Figure 18. NOTE: Inner duct cover will cover the duct cover-mounting bracket. 4. Use aluminum or steel pipe to connect the plastic exhaust on the hood to the ductwork above. Use duct tape to make all joints secure and air tight. 5. Connect electrical wires. Refer to “Wiring to Power Supply” on Pag

- Open all doors and windows to disperse the gas. If you still smell gas, call the Gas Company and Fire Department right away. CAUTION 1) For general ventilation use only. Do not use to exhaust hazardous or explosive materials and vapors. 2) To reduce the risk of fire, use only metal ductwork. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) to prevent back drafting. 3) Follow the heating equipment manufacturer’s guideline and safety standards suc

Refer Figure 15. Slide the duct cover onto the hood. 6. Use 3/16” x 3/8” screws (included) to attach duct cover to hood. Figure 15 Install Accessories Figure 16 7. Attach oil tunnel. Refer to Figure 16. 8. Refer to Figure 17. Slide the baffle filter into the hood. Push the baffle filter upward. . Slide forward. Pull downward. Fit into place. 9. For bottom casing, repeat above steps. Refer to page 17. 10. Install heating lamps (not included), 120 Volts 175 Watts max. each. Final Assembly 11.

2) Repair of any fault to be provided under this warranty shall not be provided: a) if the identification number attached to the range hood has been altered, rendered illegible or removed; b) if notice of the defect has not been given within the period applicable; c) for failure of light bulbs or heat lamps; d) for physical damage; e) for surfaces damaged by use of improper chemical cleaning agents; f) if the appliance has been: i) subject to misuse, abuse, negligence, accident, incorrect instal

All measurements in ( ) are millimeters. . All inch measurements are converted from millimeters. Inch measurements are estimated. - FOR UNDER THE CABINET MODEL NO.: CH0330SQB CH0336SQB CH0342SQB CH0348SQB - FOR WALL MOUNT - MODEL NO.: CH0330SQB CH0336SQB CH0342SQB CH0348SQB 16 - FOR WALL MOUNT (WITH OPTIONAL DUCT COVER) 17 ***Rear Knocko ut Holes ***Hood-Mounting Bracket PARTS LIST MODEL NO.: CH0330SQB CH0336SQB CH0342SQB CH0348SQB NO. DESCRIPTION MODEL /SIZE PART NO. 1 Ducting Transition FA-120

• Use an extinguisher ONLY if: a) You have a Class A, B, C extinguisher and know how to operate it. b) The fire is small and contained in the area where it started. c) The fire department has been called. d) You can fight the fire with your back to an exit. What to Do If You Smell Gas - Extinguish any open flame. - Do not try to turn on the lights or any type of appliance. - Open all doors and windows to disperse the gas. If you still smell gas, call the Gas Company and Fire Department right awa