Stimmen - 2, Durchschnittliche Bewertung: 4 ( )

Hersteller: Impex Dateigröße: 1.08 mb Dateiname: 4582e757-90bb-45d6-9b65-f7f627248fb5.pdf Unterrichtssprache:

Attach a “V”-Pulley (6) and a Long Cable Trap (50) to the Left Arm (47) in the same manner. 10. Lubricate both axles on the Top Frame (55). Slide the Right Arm (48) onto the right axle. Note: Be careful not to confuse the Right Arm with the Left Arm (47); refer to step 9 to identify the Right Arm. Be sure that the upper end of the Right Arm is behind the indicated bracket on the Top Frame (55). Tap two 1” Retainers (69) and a 1” Round Cover Cap (70) onto the right axle. Be sure that the teeth on the Retainers bend toward the Cover Cap, as shown in the inset drawing. Attach the Left Arm (47) in the same manner. Press 1 3/4” Square Inner Caps (44) into the lower ends of the Right and Left Arms (47, 48). Wet the lower end of each Arm with soapy water. Slide a 10” Pad (45) onto the lower end of each Arm. 8 44 31 3 22 17 47 6 507 50 6 Welded Brackets 21 69 70 45 44 48 47 48 44 49 46 46 49 9 10 45 Lubricate Axle Bracket 69 70 55 55 8 11. During steps 11 through 27, refer to the CABLE ASSEMBLY CABLE DIAGRAM on page 22 of this manual to verify proper cable routing. Before beginning this section, identify the Long Cable (23), the Medium Cable (58), and the Short Cable (35) by comparing the lengths and ends of the cables. IMPORTANT: While assembling the cables, do not overtighten the bolts and nuts attaching the pulleys. The pulleys must be able to turn freely. 12. Locate the Long Cable (23). Route the Long Cable around the indicated 3 1/2” Pulley (15) attached to the Top Frame (55). Be sure that the end of the Cable with the ball is on the indicated side of the Pulley and that the Cable is between the Pulley and the hook. Tighten the 3/8” x 3 3/4” Bolt (71) and the 3/8” Nylon Locknut (not shown). 13. Wrap the Long Cable (23) around a “V”-Pulley (6). Attach the “V”-Pulley and a Long Cable Trap (50) to the indicated bracket on the Front Upright (42) with a 3/8” x 2 1/2” Bolt (7) and a 3/8” Nylon Locknut (21). Be sure that the Long Cable Trap is positioned to hold the Cable in place. 14. Route the Long Cable (23) around the “V”Pulley (6) on the Left Arm (47). Be sure that the Cable is in the groove of the Pulley and that the Long Cable Trap (50) is positioned to hold the Cable in place. Tighten the 3/8” x 2 1/2” Bolt (7) and the 3/8” Nylon Locknut (not shown). 11 23 58 35 12 55 Hook Ball 71 15 23 13 7 21 42 6 50 23 14 23 6 7 47 50 9 CABLE ASSEMBLY 15. Route the Long Cable (23) around the “V”Pulley (6) on the Right Arm (48). Be sure that the Cable is in the groove of the “V”Pulley and that the Long Cable Trap (50) is turned to hold the Cable in place. Tighten the 3/8” x 2 1/2” Bolt (7) and the 3/8” Nylon Locknut (not shown). 16. Route the Long Cable (23) around the 3 1/2” Pulley (15) attached to the Pulley Bracket (20). Be sure that the Cable is in the groove of the Pulley and that the Cable Trap (66) is turned to hold the Cable in place. Tighten the 3/8” x 2” Bolt (12) and the 3/8” Nylon Locknut (not shown). Make sure that the 5/16” x 5” Bolt (68) is properly tightened and that the Pulley Bracket (20) can move freely. 17. See the inset drawing. Attach a 3 1/2” Pulley (15) and a Cable Trap (66) to the indicated hole in the Long “U”-Bracket (57) with a 3/8” x 2” Bolt (12) and a 3/8” Nylon Locknut (21). Be sure that the Cable Trap is inside the “U”Bracket. Note: This may come pre-assembled. Route the Long Cable (23) around the 3 1/2” Pulley (15) and through the Long “U”-Bracket (57). Be sure that the Cable is in the groove of the Pulley and that the Cable and Pulley move smoothly. 18. Note: The Pulley in this drawing is pre- assembled. It is shown disassembled for easy part identification. Route the Long Cable (23) around the 3 1/2” Pulley (15) attached to the bracket on the Top Frame (55). Tighten the 3/8” x 2” Bolt (12) and the 3/...

Herunterladen

Geben Sie zwei Ziffern: