Stimmen - 3, Durchschnittliche Bewertung: 4 ( )

Hersteller: ProForm Dateigröße: 857.8 kb Dateiname: e69c3108-17d8-4034-94e6-a1c7d97d016e.pdf Unterrichtssprache:

36 91 13 37 18 2 77 10 16 38. Move to the other end of the unit. Attach the remaining Backrest (41) to the Butterfly Upright (42) with two 1/4” x 2 1/2” Screws (43) and two 1/4” Flat Washers (10). 38 37. Attach the other end of the Seat (13) to the Press Seat Frame (77) with a 1/4” Flat Washer (10) and a 1/4” x 2 1/2” Screw (43). 37 43 10 13 41 43 10 42 77 39. Press a 1 1/2” Square Inner Cap (32) into the Butterfly Seat Frame (36). Insert the 1/4” x 2” Carriage Bolt (38) into the center hole in a Seat Plate (37). Attach the Seat Plate to the Seat (13) with two 1/4” x 3/4” Screws (18). Insert the 1/4” x 2” Carriage Bolt (38) into the indicated hole in the Butterfly Seat Frame. Tighten a 1/4” Nylon Locknut (2) with a 1/4” Flat Washer (10) onto the Carriage Bolt. Attach the other end of the Seat to the Butterfly Seat Frame with a 1/4” Flat Washer (10) and the 1/4” x 2 1/4” Screw (24). 39 32 13 38 10 24 10 2 18 36 37 40. Press a 1 1/2” Square Inner Cap (32) into the Leg Lever (29). Lubricate the 5/16” x 2 1/4” Bolt (33). Attach the Leg Lever (29) to the Seat Frame (36) with the Bolt and a 5/16” Nylon Locknut (3). Do not overtighten the Nylon Locknut. The Leg Lever must be able to pivot freely. Insert the 5/16” x 2” Eyebolt (35) into the Leg Lever (29) from the direction shown. Tighten a 5/16” Nylon Locknut (3) with a 5/16” Flat Washer (8) onto the Eyebolt. 41. Rest the Butterfly Seat Frame (36) on the indicated pin (A) in the Butterfly Upright (42). Attach the Butterfly Seat Frame to the Butterfly Upright with a 5/16” x 2 3/4” Carriage Bolt (14) and the Seat Knob (40). 42. Press two 3/4” Round Inner Caps (34) into each Pad Tube (28). Insert one Pad Tube into the Butterfly Seat Frame (36). Slide a Foam Pad (30) onto each end of the Pad Tube. Insert the other Pad Tube into the Leg Lever (29). Slide a Foam Pad (30) onto each end of the Pad Tube. Miscellaneous Assembly 43. Leg Press Assembly Attach the Leg Press Plate (87) to the Adjustment Tube (88) with a 5/16” x 2 1/2” Bolt (22), two 5/16” Flat Washers (8) and a 5/16” Nylon Locknut (3). Make sure the Leg Press Plate and the Adjustment Tube are oriented as shown. Press a 1 3/4” Square Inner Cap (44) into the Adjustment Tube (88). 40 33 Lubricate 35 3 29 8 3 36 32 41 40 14 A 36 42 42 3430 28 30 34 36 29 43 87 822 3 44 88 17 18 44. Attach the Adjustment Tube (88) to the Leg Press Arm (89) with the Small Lock Pin (90). Make sure the Leg Press Plate (87) is oriented as shown. 44 88 90 87 89 45 BUTTERFLY 45. Remove the decals from the decal sheets (not shown) and apply them to the home gym system in the locations shown in the illustration below. ARM PRESS LEG PRESS LEG EXTENSION/ CURL HIGH PULLEY LOW PULLEY SERIAL NUMBER DECAL 19 46. Make sure that all parts have been properly tightened. The use of the remaining parts will be explained in ADJUSTMENT, beginning on page 20 of this manual. Before using the home gym system, pull each cable a few times to be sure that the cables move smoothly over the pulleys. If one of the cables does not move smoothly, find and correct the problem. IMPORTANT: If the cables are not properly installed, they may be damaged when heavy weight is used. If there is any slack in the cables, you will need to remove the slack by tightening the cables. See TROUBLESHOOTING AND MAINTENANCE on page 22. Cable Diagram The Cable Diagram below shows the proper routing of the Short Cable (23), the Medium Cable (86) and the Long Cable (58). The numbers show the correct route for each cable. Make sure the Cables are routed correctly, that the Pulleys move smoothly and that the Cable Traps do not touch or bind the Cables. Incorrect cable routing can damage the weight system. Short Cable (23) Medium Cable (86) Long Cable (58) 1 3 4 2 8 7 5 6 9 1 2 3 4 1 3 2 4 5 6 7 8 9 Cable ID Chart Adjustment The instructions below describe ho...

Herunterladen

Geben Sie zwei Ziffern: