First release the head with the print head release lever, and then remove the paper. • Never touch the surface of the print head. • Never touch around the print head and the motor during printing or before they have had sufficient time to cool. ■ Cautions in handling the recording paper (thermal paper) • Use only paper specified by SHARP. • Do not unpack the thermal paper until you are ready to use it. • Avoid heat. The paper will color at around 70°C. • Avoid dusty and humid storage plac

. . . . . . . . . . . . . . . . . . . . . . . . . . . 1 CHAPTER 2. OPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 CHAPTER 3. MASTER RESET AND PROGRAM RESET. . . . . . . . . 6 CHAPTER 4. HARDWARE DESCRIPTION . . . . . . . . . . . . . . . . . . . . 7 CHAPTER 5. DIAGNOSTIC PROGRAM . . . . . . . . . . . . . . . . . . . . . 14 CHAPTER 6. IPL FROM EP-ROM . . . . . . . . . . . . . . . . . . . . . . . . . . 19 CHAPTER 7. CIRCUIT DIAGRAM AND PWB LAYOUT . . . . . . . . . 2

. Enlargement At the receipt side, the logo is also printed and the receipt is issued. 3 Check that: The print is free from contamination, blur, and uneven density. 4 End of testing The test will end automatically. 4) KEYBOARD TEST 1 Key operation _ _ _ _104 3 CA/AT 2 KEY check sum code 2 Test procedure The keyboard is checked using the sum check code of the key code. If the sum check code is not entered, the check is made using the sum check code of the default keyboard arrangement The sum chec

If the no battery symbol “ l ” appears, you must install the batteries at once. Install three new alkaline batteries LR6 (“AA” size) according to the procedure shown below with the AC cord connected and the mode switch set to the REG position: 1. Push the printer cover forward and detach it. Be careful with the paper cutter, so as not to cut yourself. 2. Open the battery compartment cover next to the paper roll cradle. 7 3. Insert three new alkaline batteries LR6 (“AA” size) as illustrated

The P key is needed only for fractional entry. Key operation example [#/tm/sbtl| 29 @ 15 O 00 % |C«AT/NS] Print F0?%1 000 L 15-00% -10.25% — Percentage limit ■ Function parameters for %, & and ( Procedure ) To program “0” for all items *ABCDEFGH ■ %1 or %2 © To program for another key CANS 38 *: Item:_Selection:_Entry: A Tax 4 status Taxable 1 Non-taxable* 0 B Tax 3 status Taxable 1 Non-taxable* 0 C Tax 2 status Taxable 1 Non-taxable* 0 D Tax 1 status Taxable 1

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation

When formatting is finalized, the message “SD FINAL” will be printed. In case an error occurs, a corresponding error message will be printed. 5 Saving and Restoring All the Data Set the mode switch to the PGM position. Saving (writing) all the data The comfirmation message is printed. To execute * s 144 @ s 1A l To cancel Restoring (reading) the saved data The comfirmation message is printed. To execute * s 148 @ s 1A l To cancel * The message “ACCESSING CARD” will appear and stay on the display

Never use other cables. 1 External View The printer is a receipt/journal dual station type thermal printer, and therefore it does not require any type of ink ribbon or cartridge. Lift the rear of the printer cover to remove. To re-install, hook the pawls on the cabinet and close. Caution: The paper cutter is mounted on the printer (receipt side). Be careful not to cut yourself. Print head release lever The print head can be lifted by the green lever on the right side of the printer. Pulling the

(Fixed position) 0 F Always enter 0. (Fixed position) 0 G Always enter 0. (Fixed position) 0 H Number of purchases print Allow printing of number of purchases* 0 Disallow it 1 Function selection for tax Job code: 15 * Item: A B C D E F G Always enter 0. Always enter 0. Always enter 0. Always enter 0. Always enter 0. Always enter 0. Tax delete in REG mode availability Selection: (Fixed position) (Fixed position) (Fixed position) (Fixed position) (Fixed position) (Fixed position) Allow tax delete

For department 41-99: To program zero dsDept. code Unit price (max. six digits) A To program another department, start from the beginning without pressing the Akey. Key operation example Print 1000 . A Unit price If a department is not programmed to allow the entry of preset unit prices in functional programming, the department is automatically changed to allow the entry of preset unit prices by this programming entry. 2 PLU/UPC Programming The cash register can handle PLU codes and UPC codes. P