However, with “Precise print mode” selected, feed accuracy will increase because the media is fed while the sensor threshold value is being monitored all the time. Print Head Sensor Feed direction After a page alignment is initiated, the first print start position is detected. The media is fed until this position is aligned with the Print Head position. After page alignment Before page alignment Page alignment in Strict feed mode If the tear-off is to be performed, the media will be further fed

Solutions / Reference The print tone is too high. Check the print tone. If it is too high, decrease it. . [Help] on the Printing Preferences page in the Printer Driver Properties The Print Head pressure is too high. Decrease the Print Head pressure. . Step 10 in Section 5.1 How to Load the Media A print speed is too low. Increase a print speed. The problem may be solved by adjusting a print speed and print tone. 12- 4 12. TROUBLESHOOTING ¦ White streaks appear on printout irregularly or the ribb

The register will not operate unless one of these keys is inserted and set to the corresponding position on the Clerk Locks. Each of the keys may be inserted and pulled out in the neutral position marked with the (point). Push-key Type (Alternative Option, for ten clerks) j_________This type may be installed in place * I 2 I 3, I I 5 I 0£ clerk Locks above, as an ____alternative option. In that case, 1 6.1 7 1 8—I 9TUU ten clerk keys will be installed. Each clerk is assigned to his/her own

Since every consideration has been given to safety, there is no danger of damaging the machine by incorrect operation. Please refer to this manual whenever you have any doubts concerning the machine. This machine has been manufactured under strict quality control and should give you full satisfaction. However, if the machine is damaged during transit, or there are any unclear points in this manual, please contact your local TEC representative. | The specifications described in this manual may

INTRODUCTION.........................................................................................................1- 1 1.1 Main Features ...............................................................................................................1- 1 1.2 Description of Model Number ........................................................................................1- 1 2. SPECIFICATIONS .....................................................................................................

SOUP PLU0041 $2.70 0063 13:54TM - 59 - EO-11032 ■ Changing the Whole Package Quantity (and the Price accordingly) (applicable to PLUs of Split Package Pricing type) [-► l PLU Code l [PLU1 New Whole [ST]—► New Preset [#] Package Price * Quantity max. 2 digits ; 0 to 99 > [AT/TLJ Repeatable for other PLUs. * (Repeatable from here if the PLU Code is sequential from the previous one.) ex.) To change PLU No. 61 (previously programmed three-pack with $2.50) to five-pack wit

Any sale containing amounts entered through the IRTN MDSE I key may be finalized even if the sale total is negative. - 58 - ADDRESS NO. CONTENTS Standard Bit Set 1 1 1 1 11 J l°l ‘u VALIDATION COMPULSORY I BIT NO. ITEM SELECTIVE STATUS STANDARD STATUS REMARKS l RESET FREE * IRTN MDSÉ| Key SET COMPULSORY 2 IPOI Key RESET FREE * SET COMPULSORY 3 IR7TI Key RESET FREE * SET COMPULSORY u fl RESET FREE * 11 TEN CORR 1 Kev SET COMPULSORY 5 g ey RESET F

AZ, GTZ .......................... 11 ................55 STORE NAME/MESSAGE AND COMMERCIAL MESSAGE PROGRAMMING .............. Anytime .......................... 1 ................66 CLERK NAME PROGRAMMING ........................ Anytime .......................... 1 ................68 DEPARTMENT NAME AND STATUS PROGRAMMING ........ Anytime/AZ/AZ, GTZ, PLUZ ......... 3 ................69 PLU TABLE PROGRAMMING OR CHANGING ............. PLUZ/Anytime ..................... 4 ................72

This instruction manual provides a description of the functions and handling of this register and should be read carefully to ensure optimum performance. Since every consideration has been given to safety and reliability, there is no danger of damaging the machine by incorrect operation. Please refer to this manual whenever you have any questions concerning the machine. This machine has been manufactured under strict quality control and should give you full satisfaction. However, if the machine

an error will result on entering an excessive amount through the department key). |? Any time outside a sale Mode Lock : SET / GT Lock : Neutral 8 [@/FOR] I HALC I I LALC I I_ LC for the individual dept ( [SHIFT]) “►[DEPT] for the shifted depts. I HALC I I LALC I i_: Common LC for all depts [AT/TL] Repeatable for other departments ‘ HALC .... High Amount Listing Capacity (to be set in a 2-digit code.) ex.) I 3 I I 4 I .... indicate $39.99 ^-4 digits — equal to or smaller than $39