Stimmen - 2, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
First release the head with the print head release lever, and then remove the paper. • Never touch the surface of the print head. • Never touch around the print head and the motor during printing or before they have had sufficient time to cool. ■ Cautions in handling the recording paper (thermal paper) • Use only paper specified by SHARP. • Do not unpack the thermal paper until you are ready to use it. • Avoid heat. The paper will color at around 70°C. • Avoid dusty and humid storage places. Avoid direct sunlight. • The printed text on the paper can discolor under conditions of high humidity and temperature, exposure to the direct sunlight, contact with glue, thinner or a freshly copied blueprint, and heat caused by friction from scratching or other means. • Be very careful when handling the thermal paper. If you want to keep a permanent record, copy the printed text with a photocopier. 62 A2 01 5 OPERATOR MAINTENANCE 01.11.11 10:24 AM 63 4 Replacing the Batteries This cash register displays a low battery symbol (¿_) when the batteries are low, and displays a no battery symbol ((_) when batteries are extremely low or batteries are not installed. When the low battery symbol is displayed, replace the batteries with new ones as soon as possible. The existing batteries will be dead in about two days. When the no battery symbol is displayed, replace the batteries immediately. Otherwise, if the AC power cord is disconnected or a power failure occurs, all the programmed settings will be reset to the default settings and any data stored in memory will be cleared. I Note Be sure to observe precautions shown on page 1 when handling batteries. To replace the batteries: 1. Make sure that the cash register is plugged in. 2. Turn the mode switch to the REG position with the power cord connected. 3. Remove the printer cover. 4. Open the battery compartment cover and remove the old batteries. 5. Install three new R6 or LR6 batteries (“AA” size) in the battery compartment. Be sure the positive and negative poles of each battery are facing in the proper direction. When they are installed correctly, the “ (_ ” or “ ¡_ ” symbol will disappear. 6. Close the battery compartment cover. 7. Replace the printer cover. 5 Replacing the Paper Roll Be sure to use paper rolls specified by SHARP. The use of any other paper rolls other than those specified could cause paper jamming, resulting in register malfunction. Paper specification Paper width: 57.5 ± 0.5 mm Max. outside diameter: 80 mm Quality: Thermal paper • Be sure to set paper roll(s) prior to using your machine, otherwise it may cause a malfunction. Install the paper roll in the printer. Be careful to set the roll and cut the paper end correctly. If the top end of the paper roll is fixed with paste or tape, the paper may lose its color development ability in the pasted or taped area due to the deterioration of the heat-sensitive color development component of the paper surface. This may result in nothing appearing at this location when printing. Therefore, when setting a new paper roll in the machine, be sure to cut off approximately one revolution (approx. 25 cm long). (How to set the paper roll) (How to cut the paper end) To the printer (q^ ]]A To the printer Correct Incorrect Correct Incorrect 63 -Q- A2 01 5 OPERATOR MAINTENANCE 01.11.11 10:24 AM 64 ■ Removing the paper roll When a red dye appears on the paper roll, it is time to replace it. Replace the paper roll with new one. If you plan on not using the register for an extended period of time, remove the paper roll, and store it in an appropriate place. Caution: The paper cutter is mounted on the cover. Be careful not to cut yourself. When the take-up spool is not used: 1. Turn the mode switch to the REG position with the power cord connected. 2. Remove the printer cover. 3. Cut the paper behind the printer and near the paper roll. 4. Press the Q key until the paper remaining in the printer comes out completely. 5. Remove the paper roll from the paper roll cradle. | Note^ Do not pull the paper through the printer. When the take-up spool is used: 1. Turn the mode switch to the REG position with the power cord connected. 2. Remove the printer cover. 3. Press the Q key to advance the journal paper until its printed part is out of the way. 4. Cut the paper and remove the take-up spool. 5. Cut the paper behind the printer and near the paper roll. 6. Press the Q key until the paper remaining in the printer comes out completely. 7. Remove the paper roll from the paper roll cradle. I Note Do not pull the paper through the printer. 64 -Q- A2 01 5 OPERATOR MAINTENANCE 01.11.11 10:24 AM 65 ■ Installing the paper roll Caution: The paper cutter is mounted on the cover. Be careful not to cut yourself. 1. Turn the mode switch to the REG position with the power cord connected. Remove the printer cover. Check that the print head release lever is in the printing position....