Stimmen - 6, Durchschnittliche Bewertung: 4.8 ( )

Hersteller: Honeywell Dateigröße: 248.24 kb Dateiname: RCI80BZ.pdf Unterrichtssprache:

It offers programmability, stand-alone operation, and communications with automation systems, utility control systems, or personal computers over a Z-Wave network. The RC-80ZB is equipped with a “cool blue” backlight display. Electrical rating: 24 V; 3 A; 50/60 Hz Maximum current: 2 A on any circuit, 3 A total Thermostat operating current: less than 15 mA The following requirements must be observed for installation in Europe: CE 1. This equipment must be installed in accordance with National wiring rules for the country in which it is installed. 2. Fuses must be replaced only with IEC rated components. 3. All product labels, instructions and markings relating to safety must be translated to a language, which is acceptable in the country in which this equipment is to be installed. INSTALLATION Before installing this thermostat: 1. Read all of the installation instructions carefully. 2. Read the Owner's Manual carefully. 3. Ensure that this product is suitable for your application. 4. Ensure that wiring complies with all codes and ordinances. 5. Disconnect power to the control transformer to prevent electrical shock and damage to equipment. 6. Select an appropriate location to ensure an accurate temperature reading. Location When replacing an existing thermostat, install the RC-80BZ in the same location. If the existing location doesn't meet the following criteria, choose a new location to mount the RC-80BZ. When choosing a location for the thermostat: 1. Ensure that the thermostat is mounted 5 feet above the floor and is at least 2 feet from an outdoor wall. 2. Ensure that the thermostat is located in an area where there is adequate air circulation. 3. Do not mount in the path of direct sunlight or of radiant heat generated by appliances. 4. Do not mount behind an outdoor wall, near a fireplace, or in the path of any air ducts. Document Number 13I00-60 / Rev A / May, 2007 Copyright © 1999-2007 Home Automation, Inc. All Rights Reserved 2 Removing an existing thermostat 1. Disconnect the power to the control transformer. 2. Remove the cover to the existing thermostat. 3. Disconnect the wires going to each terminal on the thermostat. Label each wire with the letter or number at the terminal. 4. Remove the existing plate or base from the wall. MOUNTING When mounting the RC-80BZ, grasp the thermostat by the sides, avoiding the keys, and unsnap the base from the face. Holding the base to the wall so that the word "TOP" is upright and facing you: 1. Mark the two mounting holes on the wall using a pencil. 2. Drill a hole using a 3/16" bit at each mounting hole marking. 3. Install the two wall anchors supplied. 4. Slide the system wires through the opening in the base. 5. Mount the base to the wall using the two #6 x 1/2" self-tapping screws supplied - See Figure 1. Figure 1 3 Connect each wire to the terminal strip on the thermostat base per the wiring diagram for your system application - See Figures 4 - 8. Form the thermostat wiring so that the cable lies flat between the terminal strip and the center of the base. Upon completion of wiring the thermostat, push all excess wiring into the hole in the wall. Plug the hole with the supplied insulating foam to ensure an accurate temperature reading by the thermostat. Align the tabs of the thermostat face with the slots of the thermostat base. Gently push the thermostat face into the thermostat base locking it into place - See Figure 2. Figure 2 Figure 3 Note: Be sure that the thermostat temperature sensor is standing up, and that it has not been damaged during installation - See Figure 3. TYPICAL WIRING DIAGRAMS CAUTION: Be sure to disconnect the power to the control transformer before removing or installing thermostat. Do not short gas valve, fan, heat relay, or cool relay...even momentarily. This will blow a non-replaceable fuse. Do not attempt to hook up to live circuits. An accidental connection to a component on the thermostat circuit board could cause damage to the thermostat. Figure 4 -Thermostat power-up for test or demonstration purposes Note: As a convenience to the installer, the compressor start up protection delay can be canceled. To cancel the delay, press the Prog key 3 times, then press the Fan key 2 times. Common wire is required in “heat only” applications Figure 5 -Single stage heat only thermostat Common wire is required in “cool only” applications Figure 6 -Single stage cool only thermostat * Common wire is required to use the display backlight in the RC-80ZB. Also use if heat, cool, or fan relay cannot supply 15mA to power thermostat, without activating. Figure 7 -Single stage heat/cool thermostat *Do not connect RC and RH together. Figure 8 -Heating & cooling with separate transformers CONFIGURING THE BACKLIGHT ON THE RC-80ZB The backlight on the RC-80ZB can be configured to one of three different modes: 1) on for 30 seconds when a key is pressed, 2) always on, or 3) always off. 1) To configure the display backlight to turn on when a key is presse...

Herunterladen

Geben Sie zwei Ziffern: