Stimmen - 3, Durchschnittliche Bewertung: 3.7 ( )

Hersteller: Hunter Fan Dateigröße: 219.31 kb Dateiname: 43153.pdf Unterrichtssprache:

3) After 15 seconds without a key press, the thermostat will r display mode. 4) When setting the program time, note the AM / PM indicator STEP 1: n Slide the System Switch to the HEAT or COOL position to program the corresponding system. NOTE: If the System Switch is in the OFF position, the last position used will be programmed. STEP 2: n Press to enter program mode. HEAT or COOL will be displayed on the LCD. STEP 3: n The Program hour and AM or PM indicator are flashing. Press to change the hour. STEP 4: n Press again to change to the minute position. The current minute will be flashing. n Press to change the minute. STEP 5: n Press again to change to the program temperature. The current temperature will be flashing. n Press to change the temperature. n Press again to move to the next program number. n Repeat Steps 3 through 5 to change the remaining Weekday and Weekend programs. (There are a total of 8 programs.) n After cycling through all 8 programs, press again to return the display to normal. n Press at any time to exit the Program Mode. repeatedly n Press and hold for about 1 second to enter Manual Override mode. When display flashes, you can release the key. n Press again to change to your desired Set Temperature. Hold the key for 2 seconds to fast-advance the Set Temperature. n Press to return to normal mode, or wait 15 seconds for it to return automatically. n The current program number will flash to signify the Temporary Override. n At the next program change time, the Temporary Override is cancelled, and the next program temperature becomes the setpoint temperature. To end the Temporary Manual Override: n Press, then press again. This will return the set temperature to the current program set temperature. Permanent Override To hold your Manual Override for vacation or just an extended period of time: n Press to make the current program temperature the HOLD temperature. HOLD will be displayed on the LCD, and the Program number will disappear. n Follow the Temporary Manual Override M FTHWT AM 1 HEAT M FTHWT AM 1 HEAT PROGRAM PROGRAM PROGRAM ect position SA PM 2 TEMP M FTHWT AM 1 HEAT SET TEMP 3 COOL TEMP PM COOL TEMP 3 SA TH PM HOLD TEMP T PM 3 HEAT TEMP PROGRAM COOLOFFHEAT AUTOONFAN ! HOLD/RET HOLD/RET HOLD/RET or or HOLD/RET Revising Programs STEP 1: DAY/TIME STEP 2: DAY/TIME STEP 3: DAY/TIME ¦ The LCD will show this information when batteries are first installed, or after the Reset button is pressed. The temperature will update after a few seconds. ¦ During time and day setting mode, the temperature and program displays will go blank. ¦ Example: Set the Thermostat to the current time of 2:16 pm on Saturday. Refer to the Steps below. M AM 4 TEMP ¦ Press to enter time and day setting mode. The current hour and the AM / PM indicator will be flashing. ¦ Press to change the Hour up or down to the current hour. Note the AM / PM indicator, as the display will change at 12 AM and 12 PM. M AM ¦ Press again to change from hour setting to minute setting. The current minute will be flashing. ¦ Press to change the Minute up or down to the current minute. M PM ¦ Press again to change from minute setting to day setting. The current day will be flashing. ¦ Press to change the Day up or down to the current day. M PM n All 7 days of the week have the same default programs. Personal Program Schedule ¦ You can revise the factory programs to match your own schedule. Use this Personal Program Schedule to determine which times and temperature settings match your comfort and energy saving requirements. Use a pencil so you can instructions above to change the revise your records each time you change your program settings. Permanent Manual Override temperature. n You can confirm the held set temperature Heating by pressing for less than 1 second. To end the Permanent Manual Override: n Press again. The thermostat will return to HOLD/RET the current program, and the HOLD display will be canceled. Day Program 1 Program 2 Program 3 Program 4 Monday – Friday Time Temp Time Temp Time Temp Time Temp Saturday – Sunday Time Temp Time Temp Time Temp Time Temp STEP 4: n Press again to change back to the SA DAY/TIME normal display. or PM HOLD/RET 2 TEMP NOTE: You may press the HOLD/RET at any time during Day and Time setting to return to the normal display. 12 Hr. / 24 Hr. Time Format Your thermostat is set from the factory in normal 12 (AM / PM) time format. To change to 24 hour (military) time, press PROGRAM at any time while the Hour, Minute, or Day is flashing to toggle between the 12 hour and 24 hour formats. The AM / PM indicator will not be displayed in 24 hour mode. Both the current time and all programs will automatically change to the selected format. PROGRAMMING The following time and temperature settings are pre-programmed into the thermostat: Temperature in F° (C°) Program Number Time Heat Cool 1 6:00 am 68°F (20°C) 78°F (26°C) 2 8:00 am 60°F (16°C) 85°F (29°C) 3 4:00 pm 68°F (20°C) 78°F (26°C) 4 10:00 pm 60°F (16°C)...

Herunterladen

Geben Sie zwei Ziffern: