Stimmen - 2, Durchschnittliche Bewertung: 3.5 ( )

Hersteller: Mitsubishi Electronics Dateigröße: 6.36 mb Dateiname: 5606674f-c6fb-65e4-e17c-b36f99757af7.pdf Unterrichtssprache:

22. GUIDE: Displays or removes TV Guide On Screen or ChannelView for ANT-1 and 2. Displays Track List for A/V Disc. Displays program guide for satellite receiver and cable boxes, or DVD Disc menu. Displays thumbnails or playlists for memory card files. 23. Light: Located on the right side of the remote control, this feature illuminates buttons or labels. 24. HOME: Exits TV on-screen menus and the TV Guide On Screen system and returns to TV viewing. 25. AUDIO: Selects individual audio settings for adjustment. 26. VIDEO: Selects individual video settings for adjustment. 27. EXCH: Exchanges PIP or POP and main TV picture. 28. SLEEP: Sets the TV to turn off within 2 hours. See the next page for setup instructions. 29 CONNECT: Initiates IEEE 1394 peer-to-peer connections. 30. FORMAT: Changes the shape and size of the main TV picture. 31. PAUSE: Pauses a live TV picture when no PIP or POP image is displayed. When PIP image is visible, pauses that image. Pauses a VCR, DVD, A/V Disc, or memory card file. 32. PLAY: Plays a VCR, DVD, A/V Disc, or memory card file. 33. FF/FWD: Fast forward a VCR or memory card file, or fast play a DVD or A/V disc. 34. STOP: Stops play of a VCR, DVD, A/V Disc, or memory card file. Remote Control, continued .............................................................................................................................. ...................................................................................................................................................................................................................................................................................................... 10111213141516123456789252423222120262728293017181931323334 Figure 1. Remote Control Overview Battery Installation Figure 2 Installing the Batteries: 1. Remove the remote control’s back cover by gently pressing the ribbed tab in the direction of the arrow and sliding off the cover. 2. Load the batteries, making sure the polarities (+) and (-) are correct. For best results, insert the negative (-) side first. ................................................ Figure 2. Operation: Installing the Batteries Care For Best Results from the Remote Control: • Be within 20 feet of the equipment. • Do not press two or more buttons at the same time unless instructed. • Do not allow unit to get wet or become heated. • Avoid dropping on hard surfaces. • Do not use harsh chemicals to clean. Use only a soft, lightly moistened cloth. • Do not mix new and old batteries. • Do not heat, take apart, or throw batteries into fire. • Use only AA alkaline batteries. Hint: If the remote is in the TV layer and does not function, press POWER and 9, 3, 5 to reset the remote. Sleep Timer Setting the Sleep Timer: 1. Press SLEEP on the remote control. 2. Each additional press of SLEEP increases the time displayed by 30 minutes up until the maximum value of 120 minutes. 3. After five seconds of inactivity, the message will disappear. 4. Press SLEEP to view the time remaining before the timer turns the TV off. Cancelling the Sleep Timer: 1. Press SLEEP to display the on-screen message. 2. Press SLEEP repeatedly until OFF is displayed. Note: After five seconds of inactivity, the message box disappears. TV Back Panel COMPONENTYPbPr (480i/480p/720p/1080i)INPUT12S-VIDEOVIDEOAUDIO- LEFT/ (MONO) AUDIO- RIGHTDTV/CABLE/ VHF/UHFANT 1 / MAINANT 2 / AUXDIGITALAUDIOOUTPUTCableCARD™ USE WITH ANT 1 CARD TOP12YPbPrAUDIO- LEFT/ (MONO) AUDIO- RIGHTOUTPUTAUDIOOUTPUTRECORDOUTPUTDVIAnalog Audio12VIDEOAUDIO- LEFT/ (MONO) AUDIO- RIGHTMONITORLINK™/HDMIVIDEO 480i/480p/720p/1080iAUDIO PCM LINEAR12IEEE 1394 INPUT/ OUTPUTNet CommandIR EMITTER .................. INPUTPC - 60HzVGA, W-VGA, SVGA, W-SVGA, XGA, 1280 X 720 4 3 5 6 2 7 1 10 9 8 1. Antenna (ANT-1 MAIN, ANT-2 AUX) ANT-1 MAIN and ANT-2 AUX can each receive both digital and analog over-the-air channels from a VHF/UHF antenna or non-scrambled digital/analog cable source. Your primary viewing signal source should be connected to ANT-1 MAIN. ANT-1 MAIN must be used to view premium subscription cable TV service authorized by the CableCARD™ access card. The CableCARD access card is provided by your local cable company. ANT-2 AUX can receive over-the-air or non-scrambled cable signals. 2. IR EMITTER NetCommand® IR Emitters connected to these jacks are used by the NetCommand system of the TV to control external analog devices such as cable boxes, VCRs, DVDs, satellite receivers and audio receivers. This system is also coordinated with the TV Guide On Screen® system for the control of cable boxes and to activate the record feature of your VCR. Either connection can be used for NetCommand functions. 3. INPUT 1 and 2 (Audio/Video 1 and 2) Inputs 1 and 2 can be used for the connection of a VCR, Super VHS (S-VHS) VCR, DVD player, standard satellite receiver or other A/V device to the TV. Please note that if S-VIDEO and VIDEO are available for the input, you must choose to connect only on...

Herunterladen

Geben Sie zwei Ziffern: