Until the final conclusions of the research are reached, you may wish to minimize your exposure to electromagnetic fields when welding or cutting. To reduce magnetic fields in the workplace, use the following procedures: For Gasoline Engines: Engine exhaust contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. For Diesel Engines: Diesel engine exhaust and some of its constituents are known to the State of California to cause cancer, birth

Box 338, Hortonville, WI 54944-0338 Tel 920-779-0916 Fax 920-779-0924 OWNER’S MANUAL TABLE OF CONTENTS A WARNING This product, when used for welding or cutting, produces fumes or gases which contain chemicals known to the State of California to cause birth defects and, in some cases, cancer. (California Health & Safety Code Section 25249.5 et seq.) The following terms are used interchangeably throughout this manual: MIG = GMAW SECTION 1 - SAFETY PRECAUTIONS - READ BEFORE USING.............

. . . . . . . . . . . . . . . . . . . . . . . . . . 12 SECTION 5 . OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 5-1. Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 5-2. Cutting Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

And if for some reason the unit needs repair, there’s a Troubleshooting section that will help you figure out what the problem is. The parts list will then help you to decide which exact part you may need to fix the problem. Warranty and service information for your particular model are also provided. Working as hard as you do - every power source from Miller is backed by the most hassle-free warranty in the business. Miller Electric manufactures a full line of welders and welding related equ

DMG EFD Remote control circuit common. EF E 0 to +10 volts dc output signal from wire feeder to power source with respect to socket D. H Voltage feedback; 0 to +10 volts dc, 1 volt per 10 arc volts. F Current feedback; 0 to +10 volts dc, 1 volt per 100 amperes. *The remaining pins are not used. 4-4. Gun Recommendation Table Process Gun GMAW – Hard or Cored Wires Roughneck C-Series Guns: 300, 400, 500, And 600 Amp. FCAW – Self-Shielding Wires FC-1260 Or FC-1150 4-5. Wire Type, Size, And Feed Spee

NationalElectricalCode,NFPAStandard70,deIaNationalFirePro-CuttingandWeldingProcesses,normeNFPA51B,deIaNationalFire tection Association, Batterymarch Park, Quincy, MA 02269. Protection Association, Batterymarch Park, Quincy, MA 02269. 1-5. Information sur les champs OlectromagnOtlques DonnOessurlesoudageOlectriqueetsureseffets,pourl.organisme, AfinderOduireeschampsOlectromagnOtiquesdansI.environnement des champs magnOtiques basse frOquence de travail, respecter Jes consignes suivantes 1 Garder es

Duty Cycle And Overheating........................................................................................................................9 3-3. Volt-Ampere Curves......................................................................................................................................9 3-4. Installing Gas Supply....................................................................................................................................10 3-5. Installing Wire Spool an

Remove all accessories from gun before servicing. Items referenced ( ) will correspond with list items. 1 Legs: Loosen set screws (23) and pull legs (not shown) straight out. Inspect legs for damage and straightness, replace if necessary. 2 Chuck (Not Shown): Insert chuck key into chuck adapter and turn key 180 degrees. Inspect chuck for damage. If taper on chuck appear worn out replace chuck. 3 Dust Bellows (3): Remove dust bellows by sliding over end of chuck adapter. The bellows prevent con

Veuillez consulter votre medecin pour obtenir plus de details. OM-2229 Page 8 OM-2229 Page 9 SECTION 3 . DEFINITIONS 3-1. Warning Label Definitions Warning! Watch Out! There are possible hazards as shown by the symbols. 1 Cutting sparks can cause explosion or fire. 1.1 Keep flammables away from cutting. Do not cut near flammables. 1.2 Cutting sparks can cause fires. Have a fire extinguisher nearby, and have a watchperson ready to use it. 1.3 Do not cut on drums or any closed containers. 2 The pl

Routine Maintenance ik ± Disconnect power before maintaining. ^ Maintain more often during severe conditions. 3 Months Replace unreadable labels WARNlrt Ji — J»w Repair or replace cracked weld cable Clean and tighten weld terminals 6 Months Blow out or vacuum inside. Remove drive roll and carrier. Apply light coat of oil or grease to drive motor shaft. 5-2. Circuit Breaker CB1 ik > 1 Circuit Breaker CB1 CB1 protects the unit from overloading of drive motor M1. If