Stimmen - 3, Durchschnittliche Bewertung: 4 ( )

Hersteller: Allied Telesis Dateigröße: 771.61 kb Dateiname: 5d5afaf5-01e7-1824-9162-012ba4973621.pdf Unterrichtssprache:

960 Stewart Drive, Suite B, Sunnyvale, CA 94085, USA All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesyn, Inc. Ethernet is a registered trademark of Xerox Corporation. All other product names, company names, logos or other designations mentioned herein are trademarks or registered trademarks of their respective owners. Allied Telesyn, Inc. reserves the right to make changes in specifications and other information contained in this document without prior written notice. The information provided herein is subject to change without notice. In no event shall Allied Telesyn, Inc. be liable for any incidental, special, indirect, or consequential damages whatsoever, including but not limited to lost profits, arising out of or related to this manual or the information contained herein, even if Allied Telesyn, Inc. has been advised of, known, or should have known, the possibility of such damages. Electrical Safety and Emission Compliance Statement Standards: This product meets the following standards. U.S. Federal Communications Commission Declaration Of Conformity Manufacturer Name: Allied Telesyn, Inc. Manufacturer Address: 960 Stewart Drive, Suite B Sunnyvale, CA 94085, USA Manufacturer Telephone: 408-730-0950 Declares that the product: Bridging Converter Model Numbers: AT-FS238a/1, AT-FS238b/1, AT-FS238a/2, AT-FS238b/2 This product complies with FCC Part 15B, Class B Limits: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device must not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Radiated Energy Note: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with instructions, may cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on. The user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and the receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. Changes and modifications not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this equipment under Federal Communications Commission rules. Industry Canada This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numerique de la classe B respecte toutes les exigences du Reglement sur le materiel brouilleur du Canada. Electrical Safety and Emission Compliance Statement RFI Emission EN55022 Class B . 1 Warning: In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. . 2 Immunity EN55024 . 3 Warning: This product requires shielded cables to comply with emission and immunity standards. If it is used with unshielded cables, the user may be required to take measures to correct the interference problem at their own expense. . 4 Electrical Safety EN60950, UL60950 . 5 Laser EN60825 . 6 Warning Class 1 Laser product. . 7 Warning Do not stare into the Laser beam. . 8 At time of installation, the Fiber Optic Lasers comply with FDA Radiation Performance Standard 21CFR Subchapter J, applicable at date of manufacture. This is a “Class 1 LED Product” (AT-FS201, AT-FS202 models) . 9 Important: Appendix B contains translated safety statements for installing this equipment. When you see the .., go to Appendix B for the translated safety statement in your language. Wichtig: Anhang B enthalt ubersetzte Sicherheitshinweise fur die Installation dieses Gerats. Wenn Sie .. sehen, schlagen Sie in Anhang B den ubersetzten Sicherheitshinweis in Ihrer Sprache nach. Vigtigt: Till.g B indeholder oversatte sikkerhedsadvarsler, der vedrorer installation af dette udstyr. Nar De ser symbolet .., skal De sla op i till.g B og finde de oversatte sikkerhedsadvarsler i Deres eget sprog. Belangrijk: Appendix B bevat vertaalde veiligheidsopmerkingen voor het installeren van deze apparatuur. Wanneer u de .. ziet, raadpleeg Appendix B voor vertaalde veiligheidsinstructies in uw taal. Important: L'annexe B contient les instructions de securite relatives a l'installation de cet equipement. Lorsque vous voyez le symbole .., reportez-vous a l'annexe B pour consulter la traduction de ces instructions dans votre langue. Tarkeaa: Liite B sisaltaa taman ...

Herunterladen

Geben Sie zwei Ziffern: