• In an area where it will come in contact with curtains, drapes, or anything that will obstruct the flow of combustion and ventilation air. • On carpet. Floor must be solid with a maximum slope of 1inch (2.54 cm). Installation in Recess or Closet: • A dryer installed in a bedroom, bathroom, recess or closet, must be exhausted outdoors. • Your dryer needs the space around it for proper ventilation. • A minimum of 120 square inches (774.2 square cm) of opening, equally divided at the top and bott

Too high temperatures may cause damage to them. ........ 2..LaundryloadingOpenthedoorandplacethetreatedlaundryintothedrumofthedryer. Tosaveenergyandachieveabetterdryingresult,pleasespinthelaundryasdryaspossible.Placethelaundryevenlyintothedrumaftershakethemloose. Note:Donotputexcesslaundryintothedryertoavoiddamagetothedryerandlaundry. 3..SettingdryingprogramTurntheprogramknobtosetanoptimaldryingprogramaccordingtothelaundrytypeandthedryingresultdesiredtoachieve. 4.DelicatefunctionsettingForthedel

Tools Required Drill & 3mm Bit 1 Philips Head Screw Driver 1 Wall Mounting Kit Includes Description 2 Hook 1 Plastic Spacers 2 Exhaust Duct 4 pieces 2. Fix the wall hanging brackets to the wall securely (eg. into the stud.) If the studs are too far apart fit a timber slat to the studs then mount the brackets onto the slat. The distance between each bracket is 155mm as per diagram. Wood Screws, 1 2g x 4 50mm Timber Screws Wall Hanging Brackets For Plaster/ Wooden Wall Ensure brackets aresecurely

Select spin time Select suitable spin time according to the laundries, and do spinning Refer list 1 of page 3 1 OFF2 3 4 5 Spin timer Take the laundry out when the spinning ends. When the spinning ends, open the top lid and the interior lid. Then take out the depression cover and laundry after the spinning drum has stopped rotation completely. Note: Refer to the Notes on Spinning carefully. Install the water inlet hose Water inlet entrance Water inlet hose The water hose should be connected as s

Electric dryer is connected to a 208 volt circuit. Drying time will be 20% longer than drying on a 240 volt circuit. Drying procedures have not been followed. See Drying Procedures, page 4. Outside exhaust hood or exhaust duct may be clogged or restricted. Clean out any obstruction. High humidity. Use a dehumidifier near the dryer. Excessive wrinkling. Dryer is overloaded. Do not overload. See Drying Procedures, page 4. Items left in dryer too long. Remove items as soon as cycle ends. Insufficie

Do not use an extension cord with this dryer. Some extension cords are not designed to withstand the amounts of electrical current this dryer utilizes and can melt, creating electric shock and/or fire hazard. Locate the dryer within reach of the receptacle for the length power cord to be purchased, allowing some slack in the cord. Refer to the electrical requirements in this manual for the proper power cord to be purchased. 3. A UL approved strain relief must be installed onto power cord. If the

Any floor unevenness should be corrected with leveling legs located on the bottom of the dryer. Tools and materials required • Phillips head and flathead screwdrivers • Channel-lock adjustable pilers • 1/2 inch open end wrench • Carpenter’s level • Measuring tape (12ft. min.) • Duct tap • Rigid or flexible metal 4 inch (102cm) duct • Vent hood Electrical requirements U.S. Only Power supply: 3 or 4 wire, 240 Volt, 30 Amp,60Hz, 1 Phase Power Supply Cord Kit (not supplied when sold in the United St

Pressing again will resume operation. 18 Francais TIMED DRY CYCLE 1. Press any button except "Off" button to power on. 2. Press "Timed-Dry Cycles" button and select "Timed Dry" cycle. • After powering on, press "Timed-Dry Cycle" button to select "Timed Dry" program. 3. Press "More Time" And "Less Time" buttons to set a suitable time. • After setting "Timed-Dry Cycle" to "Timed Dry" , you can press these two uttons to increase or decrease drying time as you desires. 4-6.Press buttons "Temp", "Cyc

• Do not excessively dry clothes to avoid wrinkles, shrinkage, roughness, electro static charges accumulation and more lint. Rack Dry cycle • This program is designed specially for articles like sport shoes. During drying please make sure the articles are placed on the rack with no risk of entangling the baffles while drum is rotating. Note: If drying rack is not in place, rolling inner tub could collide with drying rack and causes damage to the dryer and drying rack. AUTO DRY CYCLE 1.Press any