539111288 REV 01 (03/31/05) Parts Manual Collection System ©2005 Husqvarna. All Rights Reserved. Beatrice, NE. Printed in U.S.A. 2 INDEX Operators Guide Features and Controls.............................................................. 4 General Information ................................................................. 5 Safety Procedures.................................................................... 5 Unpacking Instructions .............................................................

539 108089.... 1.... WELD NUT, PLATED 10.. 539 108120.... 2.... NUT .-20 HEX NYLOC 11.. 539 990717.... 5.... NUT 5/16-18 HEX NYLOC 12.. 539 108735.... 2.... NUT .-20 HEX FLANGE 13.. 539 109552.... 2.... WASHER 3/16 LOCK 14.. 539 110321....2....BOLT, HEX 3/8-24 x 1. GR 8 15.. 539 110323....2....WASHER, HARDENED 16.. 539 113683....1....V-IDLER 17.. 539 115667....1....KEY 3/16x . 18.. 539 125229.... 1.... KEY 3/16 x 1. 19.. 539 130292.... 1.... IMPELLER 20.. 539 130293.... 1.... COVER, BELT 21.. 53

• Mower blades are sharp and can cut. Wrap the blade(s) or wear gloves, and use extra caution when servicing them. • Checkbrakeoperationfrequently.Adjustand service as shown in the Operator’s Manual. WARNING! WARNING! 7 UNPACKING INSTRUCTIONS • Remove all parts and packing materials from carton. TOOLS REQUIRED • 7/16" Wrench or ratchet and socket • ." Wrench or ratchet and socket • 7/8" Socket • Torque Wrench • Phillips Head Screwdriver • Hacksaw • Pliers NOTE: When right hand (R.H.) and left ha

Den Beutelrahmen nach vorne schieben (5) Befestigen des Schultergurtes Den Schultergurt so am BV650 befestigen, daß sich die Gurtverstellvorrichtung auf der Vorderseite befindet (6) Den Gurt nach Wunsch einstellen. ANWENDUNG • Richten Sie den BV650 nicht auf andere Personen. • Setzen Sie den BV650 nicht ein, wenn es regnet und lassen Sie ihn bei Regen nicht im Freien. • Im Saugmodus sollte das Gerät nicht ohne Schutt-Auffangbeutel eingesetzt werden. • Im Blasmodus kann der BV650 ohne Auf

• Use extra care when approaching blind corners, shrubs, trees, or other objects that may obscure vision. • The operation of any mower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your mower or performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles or standard safety glasses. • Use extra care in handling gasoline and other fuels. They are flammable and va

4. Secure with knob. Retainer Knob Outer Pulley Cover Deck Belt Shield Belt Cover Tab Middle Chute Latch 6INSTALLING MIDDLE CHUTE 1. Place middle chute over the top end of the blower assembly. 2. Latch middle chute to blower assembly. Middle Chute Blower Assembly Bagger Inlet Bagger Hood Bagger Inlet Bagger Hood ASSEMBLY 10 10 INSTALLING SPACER PLUGS 3. Secure upper chute support to hood with hex bolts, washers and nyloc nuts. 1. Remove plastic end caps from the center two bag support arms. Full

- Replace containers, close cover, and latch. b. Unlatch chutes and check for clogging. -Remove all debris in chute. -Reassemble and latch chutes. GENERAL RECOMMENDATIONS Always observe safety rules when performing any maintenance. • Before each use check for loose fasteners. • Clean unit thoroughly after each use. BLADE CARE For best results mower blades must be kept sharp. Replace bent or damaged blades. • See BLADE CARE instructions in your mower operator’s manual. CAUTION STORAGE When grass

4. Secure with knob. Retainer Knob Outer Pulley Cover Deck Belt Shield Belt Cover Tab Middle Chute Latch 1. Temporarily secure the hold down bracket to the skid plate, using a bolt and nut from the kit and the outer hole in the bracket. If needed, prop the blower housing up so it sits vertically level, but leave no more than an 1/8" gap between the deck and blower housing. Skid Plate Back-up Plate Back-up Plate 3INSTALLING HOLD DOWN BRACKET 2. Using the back-up plate as a template, drill holes i

539 109552.... 2.... WASHER 3/16 LOCK 14.. 539 110321....2....BOLT, HEX 3/8-24 x 1. GR 8 15.. 539 110323....2....WASHER, HARDENED 16.. 539 113683....1....V-IDLER 17.. 539 115667....1....KEY 3/16x . 18.. 539 125229.... 1.... KEY 3/16 x 1. 19.. 539 130292.... 1.... IMPELLER 20.. 539 130293.... 1.... COVER, BELT 21.. 539 130295.... 1.... HUB, BEARING 22.. 539 130296.... 2.... BEARING 23.. 539 130301.... 2.... BUSHING 24.. 539 130309.... 1.... COVER, OUTER PULLEY 25.. 539 130313.... 6.... NUT 5/16-1

3. OIL FOR 4-CYCLE ENGINE USE - It can cause spark plug fouling, exhaust port blocking, or piston ring sticking. 4. Mixed fuels which have been left unused for a period of one month or more may clog the carburetor and result in the engine failing to operate properly. 5. When storing the product for a long period of time, clean the fuel tank after rendering it empty. Next, activate the engine and empty the carburetor of the composite fuel. 6. When scrapping the used mixed oil container, scrap it