foot GF ressure To raise the feed dogs, push (_) For dropping the feed dogs, the lever in the direction of push the lever in the direction dial: 0 Drop feed lever the arrow as illustrated. of the arrow as illustrated. Then turn the handwheel. * Feed dogs must always be up for normal sewing. 1 Drop the feed dogs. 2. Stretch the fabric with the hole in the center between embroidery hoops, as shown. 3. Lower the presser bar and sew a_ a siow speed. 4. Move the fabric bzick and forth slowly until yo

Pour les coutures definition. Pard acabado de eosturas. Use in smocking or as a decorative stitch, Les smocks conviennent bien pour falre des ornements sur des l_sstts ldgers. Usado en av_speros y otras puntadasdecoratwas. Finish hems. sleeve and neck openings. Use on nylon tricot and other fingerie to overcast and seam. Do shell tucking on blouses and lingerie. Fin#ion des ourlets, manches el eneohlres. Surfilage et coutures sur jersey de nylon et autres v_tements de lingerie. Confection de pli

Keep IMPORTANT SAFETY ventilation openings of the sewing machine and foot controller free from accumulation of lint, dust, and loose cloth. INSTRUCTIONS 5. Never drop or insert any object into any opening. 6. Do not use outdoors. Read all instruct=on before using this sewing machine, Your sewing machine is designed and constructed only for HOUSEHOLD use. 7. Do not operate where aerosol (spray) products are being used or where oxygen is being administered. 8. To disconnect, turn all controls to t

Put the darning plate on the needle 1. Set the same as satin stitch. plate (see page 29), 2. Back the fabric with paper or 2, Remove foot holder (see page 10), Stretch Stitch 3. interfacing. Draw the letters on the fabric No pre_er foot Stretch Stitch 3. Adiust the stitch (see page 21 ), width as desired with tailor's chalk. 4. Draw the design on to the fabric F' Satin stitch foot 4. Satin stitch, adjusting the stitch Darn m9 plate with tailor's chalk. width as necessary to form each 5. Stretch

Here's How There are many ways to sewa ztgzag stitch. Consult the specific variations for detailed directions. Satin Stitch page 36, Applique Work page 37, Bar Tacking page 37, Monogramming page 38, Embroidery page 38, Button Sewing page 39, Overcasting page 40. .:. Satin Stitch Set the Machine Zigzeg width Stitch width Slllch length : e € 2 _controf2tO_l 2 3 4-s Top thread teRston (_3 contro_ 3 to 8 Stitch tenglh t control 0.5 to 1 Close to 0 Stretch Stitch F: Satin stitch foot Pressuredial: 1

Before using your new Kenmore machine, please pause for a moment and carefully read this booklet which contains instructtons on how to operate and care for your machine. Specific instructions are given on threading, tension adjustments, cleamng, oiling, etc_ Th_s wilt help you obtain the best sewing results and avoid unnecessary service expense for conditions beyond our control. Advice on the operation and care of your machine is always available at your nearest Sears Retail Store, Please rememb

needle pierces the told and the zipper 3. Place the zipper teeth next to the 1t8'" Zippertoot tape. Pied de fermetures i_ glissi_re told and pin in place. 6_ Sew through the told and the z_pper tape to the point where the slider begins. 7. Lower the needle to hold the tabric and raise the presser toot. Mise en place: 4.Pour coudre le cot@. gauche de la fermemre a glissiOre, r@tez le pted de 1. Rabattez ta ressource de couture fermemres a glissi_re iz ta gauche de gauche, comme montr_. l'aiguille

NOTE: After z_pper has been inserted, linish seam by shilling toot to s_de position through side notch. sewing sewing Use "Low Bar Sewing (6757) |or "'invisible which can be obtained Machine ZIPPER FOOT'" zipper" and "'cording", at any Sears retail store. FFRMETURES ,4 GL1SSIE'RE INVISIBLES ET BORDS GANSES FERMETURE /_ GLISS1ERE INVISIBLE BORDS GANSES R_glez ie p_ed pour que l'atguilte ptclae par le Le pied de fermetures a glissidre sere aussl Iron Cettlrat dEtpted et (tttz alle c_ salt a cheval

Couvrez la surface a respirer en ddpla_ant le de celle de l'aiguille. Les griffes d' entra_nement denteurent vtsibles tambour lentement d' avant en artiste. clans les fentes de ta platine de reprisage_ 6. Tournez ie tambour d" 1/4 de tour et refattes une Servez-vous de la platme a repriser pour: s_rte de Points sur les prenners. Repriser (voir page 45 ), REMARQUE: Si le tissu est fin ou tr_s usg, Coudre les boutons (vow page 51 ). mettez un nloreeau de tissu dessous pour renforeer l"endroit endo

At the end ot the seam, you may The seam guides on the needle plate want to reverse to lock the stitch. • Straight Stitch are there to help you measure seam 8. Raise the presser foot and remove width. The lines are 1/8-apad, with the tabric. 1. Raise the presser loot. the 5/8 °. and 7/8-lines marked. 2. Raise the needle to its highest g. Cut the threads. Straight foot Zigzag tom position. 3. Place the edge ol the labnc next to a stitching guide tlne on the needle g plate (5/8'" is most common).