Wind thread until winder stops. Push bobbin winding spindle to the left and clip thread. Remove bobbin. Turn clutch knob away from you while holding hand wheel for normal sewing operation. position Case should lock into place release when latch is released. SECTION 2. PREPARE THE MACHINE FOR SEWING Prepare the Top Thread • Thread the Needle ILuLf_ Raise take-up lever to its highest position by turning hand wheel toward you. Raise presser foot lever. Place spool on spool pin as shown, with thread

12710 385. 12712 or 385. 12714 SEARS CANADA INC. Dear Customer: You have just invested in a very fine zigzag sewing machine. Before using your new Kenmore machine, please pause for a moment and carefully read this booklet which contains instructions on how to operate and care for your machine. Specific instructions are given on threading, tension adjustments, cleaning, oiling, etc. This will help you obtain the best sewing results and avoid unnecessary service expense for conditions beyond our c

Turn the fabric a half turn and sew another Use the darning plate in the following layer of stitching over the first layer. ways: Darning (P. 22) NOTE: If your fabric is thin or badly Button Sewing (P. 26) damaged, use a separate piece of fabric under the hole to reinforce it. 7. When you finish darning, remove the darning 22 plate. SECTION 3. LEARN THE STITCHES Zigzag Stitches Basic Zigzag Set the Machine Stitch Stitch selector Top thread tension Stitch length control 2 to 5 control red Zigzag

Stop sewing at the right stitch• 6. a. b. c. Set the stitch selector at r_ m m Sew4 to 6 stitches. Stop sewing at the left stitch• 7. Remove the fabric and open with the buttonhole cut the hole opener• NOTE: When sewing at the edge of fabric, set sliding buttonhole foot as illustrated and sew in reverse( bl-->r_-_l_,_ ). _ m m UI I,_d u 6_d SECTION 4. PERFORMANCE PROBLEMS CHART What to Do When PROBLEM PROBABLE CAUSE CORRECTION Incorrect size needle, Choose correct size needle for thread and fabr

SECTION 2. PREPARE YOUR MACHINE FOR SEWING • Presser Foot Types Zigzag Foot Straight Foot To Snap On Pin To Snap On the Presser Foot: 1. Ptace the presser foot so the horizontal pin on the foot lies just under the groove of the foot holder. 2. Lower the presser foot holder to lock the presser foot in place. NOTE : If you do not hear the presser foot snap in place, press down on the presser foot holder firmly until you hear the snap. A: Zigzag foot Use this foot for both straight and zigzag stitc

Raise the presser loot and pivot the labric to the right or left. J SECTION 3. REARNTHE STITCHES Sew a Button f Set the Machine Stitrh S_it_t_, _;etector q J Top thread tension conl[OI i to 4 Stilch length control any number (not _ nece_ adjust) Use the darning plate tot button sewing (see p. 2__23. To strengthen the shank, cut the threads leaving a 20 cm (8-) tail Bring t. Set the stitch selector at °"ci='" the needle thread down through the Zigzag loot 2. Atign both holes ot the button with th

When it is covered, turn fabric 1/4 a turn and sew layer of stitching across first layer. If fabric is thin or badly damaged in hole area, you may want to put a separate piece under the hole for reinforcement. IIIIIIIIIIII IIIIIIII III IIIIIII TEMPORARY SEWING BY MACHINE No longer do you need to baste by hand! Basting by machine is easy-simply use straight stitching with longest available length setting. PiN BASTING You can sew over pins easily (if done correctly) because your presser feet are h

Presserfoot Zigzagfoot % J I {) Stitch length dia! Within green zone OVERLAPPED SEAM Box stitch is ideal for producing flat overlapped seams on almost any type of fabric and a bolder effect wilt result from sewing with a contrasting thread. Overlap the raw edges of two pieces of fabric 2" and pin or tack. Place the fabric right side up with the middle of the overlap under the center of the presser foot, so that the stitch sews just over the top and bottom raw edges. DECORATIVE EDGING Turn the ra

2 -3 Parts list................................................................ 4-5 Setting up your machine ................. :........................... 6 Spool pins, Foot control, Light/power switch Installing extension table ............................................. 6 Winding bobbin ........................................................ 7 Removing bobbin case from shuttle ............................... 8 Inserting bobbin into bobbin case .................................. 9 Inserting