567 669 The orbital sander was invented by Festool and the RS2E is the hidden champion of our line of sanders. The RS2E is a /2 sheet orbital sander with a fine, 2.5mm stroke and a real workhorse Unfortunately / sheet sanders have become more and more unpopular in recent years in the woodworking industry. They have been replaced by the widely used random orbital sander. Though random orbital sanders have a number of advantages, you can't beat / sheet sanders for smoothing out and finishing l

Failure to do this may result in serious personal injury. Keep loose clothing rolled up and out of the way of machinery and keep hair pulled back. Wear safety glasses during the entire adjustment process. Failure to comply may result in serious personal injury. Power Switch The Model G9984/G9985 must be turned ON to visually check the results of certain adjustments made to the sander; however, actual adjustments should never be performed while the machine is plugged in. Dust Collection The Model

of strokes 10 000 - 19 400 spm Abrasive stroke 2.5 mm (0.1 in.) Weight 1.5 kg (3.3 lbs.) Safety UL 745, CSA C22.2 No. 745 Symbols V Volts A Amperes Hz Hertz W Watt ~ Alternating current n0 No load speed Class II Construction rpm Revolutions per minute spm strokes per minute O Diameter Intended use The Deltex sander can be used to smooth wood, plastics, metal, steel, composite materials, paint- lacquers, filler, stopper and similar materials. Thanks to the triangular shape of the sanding pad the

Be sureswitch is off before plugging in. Carryingtools with your finger on the switch or pluggingin tools that have the switch on invites accidents. 12Remove adjusting keys or switchesbefore turning the tool on. A wrench or keythat is left attached to a rotating part of the toolmay result in personal injury. 13Do not overreach. Stand on both feet ankeep proper footing and balance at alltimes. Proper footing and balance enables bettercontrol of the tool in unexpected situations. 14Use safety equi

Installing the Sanding Belt 1. DISCONNECT THE SANDER FROM THE AIR SUPPLY! 2. Place the sanding belt over the contact wheel, as shown in Figure 5. 3. Compress the contact arm shaft by pressing the contact wheel towards the drive wheel. Slide the belt over the drive wheel until it is centered, then release pressure (Figure 6). Figure 5. Preparing the sanding belt. Contact Wheel Belt Figure 6. Attaching the sanding belt. Contact Wheel Belt Drive Wheel To avoid accidental starting, disconnect the sa

1. Press the ON switch and then the OFF switch immediately after. The sander should run just long enough to observe the track the sanding belt makes across the rollers. 2. If the sanding belt does not track on a centered path across the rollers, adjustment is necessary. 3. Disconnect the machine from the power source! 4. Loosen the check nut shown in Figure 12. Check Nut Figure 12. Belt tracking knob. 5. Turn the adjustment knob counter-clockwise to adjust the tracking upward. Turn the adjustmen

Improper oscillation. To check the sanding belt oscillation: 1. Be sure the sanding belt is properly installed and the belt tension knob and air supply are ON. 2. Turn ON the sanding belt. —If the belt oscillates without contacting the limit switches, but the oscillation time to the left and right are NOT equal, proceed to Step 7, on Page 31. 3. An adequate stream of air through the air fork gap (Figure 26) is essential for proper oscillation. If the jet of air is weak through the gap, the

Some examples of these chemicals are: • Lead from lead-based paints, • Crystalline silica from bricks and cement and other masonry products, • Arsenic and chromium from chemically-treated lumber. The risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals work in a well ventilated area and use approved safety equipment, such as dust masks that are USER MUST READ AND UNDERSTAND IN-specially designed to filter out micro- STRUCTI

Systainer Many Festool products are shipped in a unique system container, called "Systainer". This provides protection and storage for the tool and accessories. The Systainers are stackable and can be interlocked together. They also can be interlocked atop Festool CT dust extractors. 7.17.27.3 - Place one systainer on top of the other. - Release all four latches on the lower systainer by pulling back at their top edges (7.1). - Slide all four latches upward (7.2). -Snap all four latches back to

Manual de instrucciones Pagina 12 - 16 IMPORTANTE: Lea y comprende todas las instrucciones antes de usar. 469 537_001 1 General safety rules Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fi re and/ or serious personal injury. SAVE THESE INSTRUCTIONS 1) Work area safety a) Keep work area clean and well lit. Cluttered and dark areas invite accidents. b) Do not operate power tools in explosive atmospheres, such as in the presence