Stimmen - 2, Durchschnittliche Bewertung: 4.5 ( )

Hersteller: Festool Dateigröße: 1.97 mb Dateiname: Unterrichtssprache:

1. Press the ON switch and then the OFF switch immediately after. The sander should run just long enough to observe the track the sanding belt makes across the rollers. 2. If the sanding belt does not track on a centered path across the rollers, adjustment is necessary. 3. Disconnect the machine from the power source! 4. Loosen the check nut shown in Figure 12. Check Nut Figure 12. Belt tracking knob. 5. Turn the adjustment knob counter-clockwise to adjust the tracking upward. Turn the adjustment knob clockwise to adjust the tracking downward. 6. Once sanding belt is consistently tracking across the center of the rollers, tighten down the check nut that was loosened in Step 4. Main Table Height The main table is adjustable to accommodate a wide range of workpieces and sanding operations. Because the main table is designed with a special balance mount, it is easily adjusted up and down. To adjust the main table: 1. Loosen the lock handles on the front of the sander. 2. Move the main table to the desired height as shown in Figure 13. 3. While holding the main table at the desired height, tighten the lock handles loosened in Step 1. Figure 13. Adjusting main table height. -16 G9984/G9985 Oscillating Belt Edge Sander Main Table Angle The main table position can be adjusted from 0° 45°. To adjust the angle position of the main table: 1. Loosen the lock handles underneath each end of the main table as shown in Figure 14. 2. Tilt the table into the desired position. The scale on the side of the bracket can help you find specific angles. While holding the table in the desired position, tighten each of the locking handles loosened in Step 1. 3. Changing the table angle may reduce the clearance between the inside edge of the table and the sanding belt surface. If there is less than 1.16" clearance, loosen the fixing bolts located on the underside of the table mounting bracket as shown in Figure 14. Pull the table and mounting bracket away from the sanding belt so there is at least 1.16" clearance between the inside edge of the table and the sanding belt surface. 4. While holding the main table in the desired position, tighten the fixing bolts loosened in Step 3. 5. Recheck the clearance between the main table and the sanding belt. Repeat Steps 3 and 4 if necessary. Figure 14. Main table angle adjustment lever. 1 of 2 Lock Handles 1 of 2 Fixing Bolts Adjust this pointer to set scale accuracy. 6. We recommend using a square to adjust and/or verify the main table angle scale accuracy as shown in Figure 15. Figure 15. Setting main table to 90°. Miter Gauge The main table has a stationary miter gauge that is used to hold the workpiece at various angles against the sanding belt. To adjust the miter gauge: 1. Loosen the lock handle shown in Figure 16. 2. Rotate the miter gauge to the desired angle. 3. While holding the miter gauge in the desired position, tighten the lock handle loosened in Step 1. 4. We recommend using a square to adjust and/or verify the miter gauge scale as shown in Figure 17. Figure 16. Main table miter gauge. Lock Handle Adjust this pointer to set scale accuracy. G9984/G9985 Oscillating Belt Edge Sander -17 Figure 17. Setting miter gauge to 90°. Side Table Height The side table can be adjusted to accommodate a wide range of workpieces. To adjust the side table: 1. Loosen the lock handle shown in Figure 18. 2. Move the side table to the desired height. 3. While holding the side table at the desired height, tighten the lock handle loosened in Step 1. Side Table Angle The side table can be adjusted to accommodate sanding at various angles. To adjust the angle position of the side table: 1. Loosen the lock handle underneath the side table shown in Figure 19. 2. Move the side table to the desired position. 3. While holding the side table in the desired position, tighten the lock handle loosened in Step 1. Lock Handle Figure 19. Lock handle for side table angle. Lock Handle Figure 18. Lock handle for side table height. -18- G9984/G9985 Oscillating Belt Edge Sander SECTION 6: OPERATIONS Test Run ! Disconnect power to the machine when performing any maintenance, assembly or adjustments. Failure to do this may result in serious personal injury. Keep loose clothing rolled up and out of the way of machinery and keep hair pulled back. Wear safety glasses during the entire operation process. Failure to comply may result in serious personal injury. Always wear a dust mask when operating the Model G9984/G9985. Using this machine produces sawdust which may cause allergic reactions or respiratory problems. Once assembly is complete and adjustments are done to your satisfaction, you are ready to test run the machine. Turn on the power supply at the main panel. Press the START button. Make sure that your finger is poised on the switch, just in case there is a problem. The machine should run smoothly, with little or no vibration or rubbing noises. Strange or unnatural noises should be investigated and corrected before ope...

Herunterladen

Geben Sie zwei Ziffern: