Stimmen - 2, Durchschnittliche Bewertung: 3.5 ( )

Hersteller: Alvarion Dateigröße: 3.11 mb Dateiname: ug_1000s_1000sw.pdf Unterrichtssprache:

If they are not, see “Diagnosing connection problems” on page 21. The BROADBAND LINK indicator light will not turn green until the HomePortal software has been installed and an Internet connection has been established. Continue from here to Step 3 “Install the HomePortal Software” on page 14. 9 Home Phoneline Networking (HomePNA) Connection Requires a computer with a HomePNA port or an external HomePNA adapter Computers connected with HomePNA access the HomePortal’s Internet connection and other computers on the network using existing telephone wiring. You will need one adapter for each computer that you are connecting through HomePNA. If your computer does not have a HomePNA port, you will need to install a PCI HomePNA adapter or an external HomePNA adapter. Specific instructions for installing HomePNA network adapters can be found in the individual adapter’s package (if purchased separately) or on your HomePortal Setup Wizard CD (if included with your HomePortal). The HomePNA adapter shown in this example is a 2Wire PC Port Phoneline Adapter. 1. Connect the provided AC power adapter from the HomePortal’s POWER port to an electrical outlet. The green POWER light on the front of the HomePortal should come on. 2. Connect the provided telephone cable from the PHONE LINE port on the HomePortal to a telephone jack with DSL service. 3. Install your HomePNA adapter according to the manufacturer’s instructions. Note: If you are installing a phoneline filter, it must be installed directly between the telephone and the wall jack, as shown in the diagram. Do not connect the telephone line from the HomePNA adapter to the phoneline filter. The network will not work properly if the phoneline filter is connected directly to the HomePNA adapter. You can use the provided Y-adapter to connect both the HomePNA adapter and the phoneline filter to the same phone jack. 10 Note: Your HomePNA card or adapter is not the analog V90 dial-up modem that may be integrated in your computer. Please make sure that you connect both separately. Check your connections With your computer completely started, verify the POWER and HOME NETWORK indicator lights on the front of the HomePortal are green. If they are not, see “Diagnosing connection problems” on page 21. The BROADBAND LINK indicator light will not turn green until the HomePortal software has been installed and an Internet connection has been established. Continue from here to Step 3 “Install the HomePortal Software” on page 14. Network with Ethernet Hub or Switch Computer has Ethernet adapter and you are using an Ethernet hub or switch Note: The HomePortal has an auto-crossover port. You do not need to use a special crossover cable or make any changes to the configuration of your HomePortal, Ethernet hub, or switch. The HomePortal will establish the type of port needed during setup. 1. Connect the provided AC power adapter from the HomePortal’s POWER port to an electrical outlet. The green POWER light on the front of the HomePortal should come on. 2. Connect the provided Ethernet cable from the LOCAL ETHERNET port on the HomePortal to an open port on the hub or switch. 3. Connect the first computer’s Ethernet adapter to the hub or switch using an Ethernet cable. 11 4. Connect the provided telephone cable from the PHONE LINE port on the HomePortal to a telephone jack with DSL service. 5. Using another Ethernet cable (not provided), connect any additional computers to the hub or switch. 6. Plug the hub or switch into an electrical outlet. Check your connections With your computer completely started, verify the POWER and HOME NETWORK indicator lights on the front of the HomePortal are green. If they are not, see “Diagnosing connection problems” on page 21. The BROADBAND LINK indicator light will not turn green until the HomePortal software has been installed and an Internet connection has been established. Continue from here to Step 3 “Install the HomePortal Software” on page 14. Wireless Connection Model 1000SW only Requires a computer with 802.11b wireless adapter installed 1. Connect the provided AC power adapter from the HomePortal’s POWER port to an electrical outlet. The green POWER light on the front of the HomePortal should come on. 2. Connect the provided telephone cable from the LINE port on the HomePortal to a telephone wall jack. 3. Install your wireless adapter according to the manufacturer’s instructions (see note below). Note: If you use a 2Wire wireless adapter (PC card or USB adapter) for wireless networking, the HomePortal Setup Wizard software automatically configures it to communicate with the HomePortal during setup, but you will need to install the driver. See Appendix A for detailed installation instructions. 12 If you are NOT using a 2Wire wireless adapter, you will need to manually configure your adapter of choice to communicate with the HomePortal BEFORE installing the HomePortal software. See Appendix B for detailed configuration instructions. Check your conne...

Herunterladen

Geben Sie zwei Ziffern: