15). FIG. 15 ADJUST WHEELS FOR CULTIVATING (See Figs. 16 and 17) • Place blocks under right hand side of tiller and remove hairpin clip and clevis pin from right hand wheel. • Move wheel outward approximately 1 inch (2.5 cm) until hole in inner wheel hub lines up with inner hole in axle. • Replace clevis pin and hairpin clip on inside of wheel and remove blocks. • Repeat preceding steps on left hand side. NOTE: In extremely rough conditions and while cultivating, the wheels should be moved outwa

Always wear sturdy shoes and avoid wearing bulky or loose clothing while operating equipment. Never operate equipment when tired or while under the influence of drugs or alcohol. In case of emergency, know how to stop the equipment and thoroughly understand the. operation of ALL controls. Never permit anyone to operate equipment without proper instructions. Children'should not be permitted to operate the tractor or rotary tiller. KEEP CHILDREN AND PETS AT A SAFE DISTANCE DURING OPERATION. The tr

52¿ Сф1^А(Й CONTENTS Page INTRODUCTION AND DESCRIPTION..................................................................................................................................................................................................2 SAFETY • General Tiller Safety.......................................................................................................................................................................................................................

Honda Motor Co., Ltd. reserves the right to make changes at any time without notice and without incurring any obligation. The manual should be considered a permanent part of the tiller and remain with the tiller when sold. Read the manual carefully. Pay special attention to statements preceded by the following words: - Indicates a strong possibility of severe personal injury or loss of life if instructions are not followed. CAUTION: Indicates a possibility of personal injury or equipment damage

Do not operate the unit with the blade clutch partially engaged. Premature belt wear and clutch failure will result from improper operation of the clutch. BLADE CLUTCH CAUTION: Use extreme care when operating the blade. Inspect the work area for foriegn objects that could cause damage to the unit or injure the operator if struck by the blade. Never operate the blade with bystanders in the work area. Lever Down Engages Clutch Lever Up Disengages Clutch Lever Handle Fig. 1.1 The best performance i

If you can not locate a servicing dealer in your area you can contact the manufacturers national service organization. To reach: Briggs & Stratton: 800-233-3723 American Honda: 800-426-7701 Blade Drive Belt NOTE: When sharpening the blade it is a good idea to check the balance of the blade. A properly balanced blade will increase life of the bearings and other components. Tools required: 5/8 inch socket, torque wrench, adequate support. 1. Disconnect spark plug wire. 2. Support front of unit to

F101001A Operator Owner's Manual T h a n k Y o u f o r S e l e c t i n g 1 3 Specifications The Powerful BC2401 SELF-PROPELLED BRUSH CUTTER UNIT SIZE: OVERALL LENGTH: 82.5"(2.09 m) OVERALL WIDTH 32.0" (0.81m) OVERALL HEIGHT43" (1.09m) ACCESSORIES NUT REPLACEMENT KIT P/N 500208. To replace stripped or damaged insert nuts in engine base. BLADE BC2401 P/N 500210. Original Equipment Blade for replacement. BELT TRACTION DRIVE P/N 500119. Traction Drive Belt for BC2401 BELT BLADE DRIVE P/N 500237. Bla

This manual should be considered a permanent part of the tiller and remain with the tiller when sold. Pay special attention to statements preceded by the following words: Enm Indicates a strong possibility of severe personal injury or death if in- structions are not followed. CAUTION: Indicates a possibility of personal injury or equipment damage if instructions are not followed. NOTE: Gives helpful information. If a problem should arise, or if you have any questions about the tiller; consult an

All information in this publication is based on the latest product in- formation available at the time of approval for printing. The illustrations in this manual are based on the FR500 tiller. Honda Motor Co., Ltd. reserves the right to make changes at any time without notice and without incurring any obligation. No part of this publication may be reproduced without written permission. This manual is considered a permanent part of the tiller and it must stay with the tiller if resold. READ THIS

Rotary tine inspection/replacement Wear heavy gloves to protect your hands. Check for worn, bent or other damaged of the rotary tines. Check for damage dor loose bolts and nuts. Tighten and/or replace them if necessary. IMPORTANT NOTICE 1 Use only a genuine HONDA replacement rotary tine. Rotary tine A and rotary tine B are not interchangeable. Bolt and nut directions Rotary tine locations 10 mm BOLTS 10 mm NUTS/ 10 mm SPRING WASHERS A h 6. STOPPING THE ENGINE 1. Move the throttle to the idle pos