Stimmen - 2, Durchschnittliche Bewertung: 5 ( )

Hersteller: Moyer Diebel Dateigröße: 5.87 mb Dateiname: manual147.pdf Unterrichtssprache:

Optional Equipment (consult factory) 70°F/39°C rise built-in booster heater 70°F/39°C rise booster heater element-P/N 111233, Gasket- P/N 109985 1-RDT Right-hand sink - P/N 403562 1-RDT Left-hand sink - P/N 403561 17" Stand - P/N 0708757 17" Storage cabinet - P/N 0703593 6" Stand - P/N 0712393 Peg dish rack - P/N 101285 Flat-bottom dish rack - P/N 101273 Drain water tempering kit - 0712382-1 1 Installation Receiving NOTE: The installation of your dishwasher must be performed by qualified service personnel. Problems due to improper installation are not covered by the Warranty. 1. Inspect the outside of the dishwasher carton for signs of damage. 2. Remove the carton and inspect the dishwasher for damage. 3. Check for any accessories that may have shipped with your dishwasher. 4. Turn to the front of this manual and follow the instructions to register your machine online. 5. Move the dishwasher near its permanent location. CAUTION: Be careful when lifting and moving the dishwasher to prevent damage to the machine. NOTE: The installation of the dishwasher must comply with local health codes. 6. Compare the installation site utility connections with the dishwasher utility connections and make sure they are the same. 7. The dishwasher can be installed as a free-standing unit or under a built-in counter-top. The typical counter-top height in most locations is 34" [86cm]. 8. Under counter installations should provide storage space for the dishwasher chemical supply containers. Containers must not be placed above the floor. 9. Chemical supply containers should be placed as close to the machine as possible. 10. Place the dishwasher in its permanent location. 11. The dishwasher has 4 adjustable feet for leveling. 12. Level the dishwasher front-to-back and side-to-side. Counter-topWall3" [8cm] Min. 34" [86cm] Min. Floor 2 Installation Electrical Connections For Model 201HT, 401HT, and 501HT machines beginning with S/N 14236 and above 1. Refer to the connection diagrams below. 2. Models 201HTN /LT, 401HTN, 501HTN /LT are equipped with a 4 ft. power cord/plug and only require a 115VAC,15A receptacle. 3. Models 201HT, 401HT, and 501HT 1 PH machines require a 3-wire plus ground supply which includes a current carrying neutral. 4. Models 201HT, 401HT, and 501HT 3 PH machines require a 4-wire plus ground supply which includes a current carrying neutral. 5. Power connections are made at the Main Terminal Block (MTB) which is located at the lower right-hand side of the dishwasher directly behind the lower front access panel. 6. Remove the MTB cover and 2 screws holding the MTB to the machine base. Then, pull the MTB up and forward to make the electrical connections. 7. Provide a 3 ft. service loop in the supply cable for servicing. 8. Re-install the MTB and the lower front access panel to complete the installation. Pull the MTB out to wire main incoming power. L1L2L3N208-230VAC208-230VAC208-230 VAC115VACGRD(For machines beginning with S/N 14236 and above) THREE PHASE POWER CONNECTIONModel 201HT, 401HT, 501HTHOW TO CONNECT 3 PHASE POWER1. Check the data plate on the front of the dishwasher for the phase of the machine. .2. Remove the lower access panel. 3. Pull power connection box forward and out. 4. The Main Terminal Block has terminals for L1, L2, L3, Neutral and Ground. 5. Connect ground, then connect L1, L2, L3 to 208-230VAC. 6. Connect a current carrying neutral to N. 7. Main power connections are complete. If the data plate says the machine is 3 Phase, then connect a 3 PH power supply. .................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................... ATTENTIONModels 201HTN, 201LT, 401HTN, 501HTN, 501LT are equipped with a 4 ft. power cord and plug...

Herunterladen

Geben Sie zwei Ziffern: