Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
4 Use the MULTI CONTROL % / fi (or the % / fi keys) to select the "MIDNIGHT2", "MIDNIGHT1" or "OFF" setting. 1 "MIDNIGHT2": Large effect Suitable for late-night use. 2 "MIDNIGHT1": Medium effect 3 "OFF" . The adjustment item is displayed for approximately 20 seconds. . Some DOLBY DIGITAL or DTS software may not be compatible with the Midnight mode. 5 Press the SOUND key again to return to the input indication. Display dimmer adjustment The dimmer function lets you select the brightness of the receiver's display. You might find this useful if you darken your room to watch movies or listen to music. Each time you press the DIMMER key, the display’s brightness changes among the three available settings. Select the brightness level you find most pleasing. 1 Bright 2 Dark 3 Dark (LEDs on the receiver are also OFF.) Sleep timer The sleep timer function turns the receiver OFF (to the standby mode) automatically when the set timer period has elapsed. The sleep timer period can be set in 10-minute steps up to 90 minutes. Press the SLEEP key repeatedly until the desired period before turning the receiver OFF (standby mode) is displayed. . Each press increments the sleep timer period by 10 minutes. 10 = 20 = 30 .....70 = 80 = 90 = Cancel = 10 = 20 = ... The sleep timer indicator lights up . Pressing the SLEEP key after the sleep timer has started allows you to check the remaining time period. . To cancel the sleep timer, turn the receiver OFF (standby mode) or press the SLEEP key repeatedly until the Sleep timer indicator disappears. 38 EN Basic remote control operations for other components The remote control supplied with this receiver is also capable of controlling components from a variety of manufacturers once you register the appropriate setup codes into the remote control unit. Low battery warning Replace all two batteries with new ones when you notice a shortening of the distance from which the remote control will operate. The remote control is designed to retain setup codes in memory while you change batteries. Registering setup codes for other components When the setup code defined for remote control of every system component is registered in one of the input selector keys of the remote control unit, you can control that component simply after selecting it using the corresponding input selector key of the remote control unit. . When recording audio on a VCR or MD recorder, for example, you can also control the system component by switching only the remote control unit, without switching the input source of the receiver. SOURCE LED Numeric keys Input selector keys TV MODE REMOTE SETUP 1Find the setup code of the component to be registered. Refer to the setup code lists to find the setup code for the component to be registered. qr Example: To register a DVD made by KENWOOD, you would enter "0490" or "0534". 2Press the input selector key (DVD, VIDEO 1, VIDEO 2, AUX, F.AUX, GAME or TV MODE) you want to register a system component. The following table shows the type of components that can be registered in each input selector key. Input selector key Registerable component Input jacks where the component is connected DVD DVD player DVD VIDEO 1 VCR VIDEO1 VIDEO 2 Satellite Receivers Cable Converters VIDEO2 AUX CD player, MD recorder (KENWOOD) AUX F. AUX Game player (Default: Xbox), DVD player FRONT AUX GAME Game player (Default: Play Station2), DVD player GAME TV MODE TV (including TVs incorporating VCR) - . Make sure that a source belonging to the registerable component is connected to the corresponding input jacks on the receiver. . A second DVD recorder, CD player or VCR can also be connected by changing the assignment of the registerable component devices. See "Re-assigning device keys" on page 40. 3Press and hold the REMOTE SETUP key until the LED blinks twice, then release the REMOTE SETUP key. . Proceed to the next steps in less than 10 seconds after the LED blinks twice. 4Press the numeric key to enter the four-digit code for the component to be registered. . The LED blinks twice when registration is completed successfully. 5Ensure that the registered component functions properly. To ensure the proper function, perform the following operation and check if the component functions as intended. Point the remote control unit to the component and press the SOURCE key (or the TV key if the component is a TV) once. If the setup code is registered properly, the component should be turned ON or OFF. If the component is a VCR, turn the VCR ON and load a video tape and perform an operation such as playback. The VCR should function as controlled if its setup code is registered properly. If the component does not function properly: If more than one setup code is listed for the component, try registering another setup code by performing steps 3 to 5. . Repeat steps 1 to 5 above to register the setup code of another component. . To change the registered setup code, register a new setup code again by performing steps 1 to 5...