Faulty Solenoid2. Wire broken or not connected3. Flow control stem screwed down, shutting valve off4. Programming is incorrect1. Faulty valve2. Particles of dirt or debris stuck in valve3. Valve diaphragm faultyTimer will not power upStations continue to turn on and off when they are not programmed to1. Transformer is defective or is not connected correctly2. Programming is incorrect3. Timer is in OFF mode1. Water pressure is too high2. More than one start time is programmed3. Stations are set t

• Plug in the transformer. WARNING: Do not link two or more sprinkler timers together with one transformer. 4. Connect Valve Wires to Timer, Pump Start and Master Valve Sockets A. Wire the Electric Valves NOTE: If the distance between the sprinkler timer and valves is under 700’ (210 m), use Orbit® sprinkler wire or 20 gauge (AWG) plastic jacketed thermostat wire to connect the sprinkler timer to the valves. If the distance is over 700’ (210 m), use 16 gauge (AWG) wire. • Taking the sprinkler wi

Correcting the Fault 1. First, repair the short in the wiring or replace the faulty solenoid. 2. Test the station by operating a manual watering sequence. 3. If the short is not detected after a few seconds, the fault notification message will be terminated. 4. If the message continues, a short in the wiring still exists. Internal Auto-Resetting Electronic Circuit Breaker The sprinkler timer is equipped with an internal electronic self-resetting circuit breaker. Possible causes of a circuit brea

If the remote is not functioning properly or if you are adding a new remote or RF sensor to your system do the following: • With the remote device in your hand press the “RF Sync” button on the timer (this will activate a red light on the timer). • Press the OFF button on the remote or depress the stem of the RF sensor (the red light should start blinking). • If the red light blinks you have successfully synchronized the devices. If the light does not blink check that the remote has a fresh 9V b

Programas dobles El temporizador incluye dos programas: Programa A y Programa B, lo que le proporciona una flexibilidad de riego. Puede asignar cualquier estacion de riego a cualquiera de los dos programas. Por ejemplo, puede asignarle al Programa A las estaciones programadas para regar el jardin y canteros todos los dias comenzando a las 8 de la manana; mientras que puede asignarle al Programa B las estaciones programadas para regar su cesped cada tres dias, comenzando a las 5 de la manana. Sei

Printed piece must meet designated specifications on this form. colors color non printing color non printing Registration PMS ???? PMS 280 PMS ???? BLACK p 801 295 9820 f 801 951 5815 1065 South 500 West Bountiful, Utah 84010 additional instructions: · ST2-RF SPRINKLER TIMER MANUAL RF SYNCACTIVEBYPASSNO WATERINGDAY / PERIOD MODELS: 57926, 57922, 57916, 57912, 91916, 91912, 91926, 91922, 94916, 94912, 94926, 94922 PN 57926-24 Rev A Section 1: Introduction Thank you for selecting an Orbit® Signatu

This high-end feature means your programming won’t be lost or erased if the power and batteries go out. Easy-to-Read Back-Lit LCD Display The timer’s back-lit blue LCD display screen is easy to read under any lighting conditions. Choice of Five Languages You can easily set the LCD display to read in any of five languages: English, Spanish, French, German or Italian. Water Budgeting This convenient feature provides a quick, easy way to increase or decrease the watering durations of all stations i

• With the dial in the AUTO position press the MANUAL button. • Press the NEXT button. • The display reads “MANUAL ALL” to the right of the letters “A” and “B.” • Press the ENTER button. Each station with a set duration will water in sequence. To quickly advance from one station to the next press NEXT . To abort this process before the manual watering is finished, press CLEAR . Otherwise, the timer will automatically exit the “MANUAL ALL” mode after all stations have run. Manual Watering - Progr

The water drop will disappear. Set the Timer to Automatically Run Your Programs: • Turn the selection dial to AUTO. The timer will be controlled automatically by the programming parameters that have been set. To Turn All Watering Off: • Turn the selection dial to OFF. This prevents the timer from turning any watering station on at any time, regardless of programming. To Prevent Watering on a Particular Day: There may be one or more days of the week when you never want to have the water turn on,

• Press the RAIN DELAY button. • Press the NEXT button until the desired language is shown in the display. • Exit the language selection mode by turning the selection dial or pressing the RAIN DELAY button. Set the Time of Day and Date If this is the first time the timer has been programmed, press the small recessed RESET button. • Turn the selection dial to TIME/DATE. • The top line of the display reads “SET TIME.” Set the current time by pressing either the or button. NOTE: To move faster thro