Stimmen - 4, Durchschnittliche Bewertung: 4.5 ( )

Hersteller: Hitachi Dateigröße: 615.24 kb Dateiname: 93305.pdf Unterrichtssprache:

26. Spraying hazardous materials may result in serious injury or death. Do not spray pesticides, acids, corrosive materials, fertilizers, and toxic chemicals. 27. WARNING: The brass components of this product contain lead, a chemical known to the State of California to cause birth defects (or other reproductive harm). (California Health & Safety Code § 25249.5, et seq.) Note: Performance of the compressor (if powered by line voltage) may vary depending on variations in local line voltage. Extension cord usage may also affect tool performance. WARNING: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Unpacking When unpacking, check to make sure the product is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible. For technical questions, please call 1-800-444-3353; SKU 93305 Page 5 Troubleshooting section at end of manual. Air Connection For best service you should incorporate a regulator and inline filter, as shown in the diagram above. Hoses, couplers, regulators, and filters are all available at Harbor Freight Tools. Note: Compressor pumps discharge condensed water, oil, or other contaminants along with the compressed air. Condensation causes “fish eyes” to appear in paint patterns. To avoid this problem, install water/oil removal filters and controls (not included) as close to the Spray Gun as possible. If run through the Gun, water and oil will cause damage. 1. You will need to prepare a 1/4” air connector (sold separately) to connect to the air inlet on the Spray Gun. First, wrap the 1/4” air connector (not included) with pipe thread seal tape before threading it into the Air Inlet (36). Connect the Red Air Hose (41) to the Air Outlet Connector (36). Attach the other end of the Red Air Hose (41) to the Air Inlet (80) on the Gun. 2. Set the air pressure on your compressor to 30-43 PSI. Do not exceed the maximum air pressure of 43 PSI. Also, set the air pressure on the Air Regulator to 10-30 PSI, as shown on the Gauge (38). 3. Check the air connection for leaks and then disconnect the tool from the air source. Control Layout FIGURE 1 Pattern Control Knob (57) Trigger (78) Air Cap Set (45) Fluid Control Knob (67) Fluid Inlet Air Adjustment Knob (73) Air Inlet (80) For technical questions, please call 1-800-444-3353; SKU 93305 Page 6 Troubleshooting section at end of manual. IMPORTANT: Before using for the first time, the spray gun must be cleaned using a solvent based thinner. If not removed, the red oil used by the manufacturer for testing and corrosion protection may contaminate paint. IMPORTANT: The Spray Gun must be cleaned immediately after use. Improper cleaning is a common reason for the Spray Gun not to work. FIGURE 2 Fluid Flow Knob (11) Air Outlet Connector (36) Safety Valve (2) Fluid Outlet (39) Air Inlet Connector (36) Air Regulator (24) A Comparison: Conventional versus HVLP Spray Guns Because conventional spray guns require a much higher air cap pressure to atomize the paint than HVLP Spray Guns, conventional guns have lower transfer efficiencies and more overspray. This translates to a significant paint/material savings for HVLP guns, in addition to making them more environmentally friendly. To qualify as HVLP, the dynamic air pressure going in the Air Cap must be a maximum of 10 PSI. The lower the air pressure, the less bounce back and overspray. Note: Due to the viscosity of latex and other water-based paints, they are not recommended for use with this or other HVLP (High Volume Low Pressure) sprayers. See FIGURE 3 below. Conventional FIGURE 3 HVLP For technical questions, please call 1-800-444-3353; SKU 93305 Page 7 Troubleshooting section at end of manual. IMPORTANT: Before using for the first time, the spray gun must be cleaned using a solvent based thinner. If not removed, the red oil used by the manufacturer for testing and corrosion protection may contaminate paint. IMPORTANT: The Spray Gun must be cleaned immediately after use. Improper cleaning is a common reason for the Spray Gun not to work. Preparation Note: Proper paint material mixture helps to ensure less problems. Be sure to follow the manufacturer’s directions. Most materials will spray readily if they are thinned properly. General tips for Preparation: 1. Mix and thin the paint/materials thoroughly according to the manufacturer’s directions. 2. Carefully strain the paint/material through a paint strainer or piece of cheese cloth. 3. Remove (un-thread) the Cup (16) from the Unit. Fill the Cup (16) to approximately 3/4 full. Thread it back onto the unit. Connect the Fluid Hose (40) form the Fluid Outlet (39) to the Fluid Inlet on the Spray Gun. 4. Start the air compressor. 5....

Herunterladen

Geben Sie zwei Ziffern: