Stimmen - 3, Durchschnittliche Bewertung: 3.3 ( )

Hersteller: Harbor Freight Tools Dateigröße: 615.24 kb Dateiname: 93305.pdf Unterrichtssprache:

Connect the Red Air Hose (41) to the Air Outlet Connector (36). Attach the other end of the Red Air Hose (41) to the Air Inlet (80) on the Gun. 2. Set the air pressure on your compressor to 30-43 PSI. Do not exceed the maximum air pressure of 43 PSI. Also, set the air pressure on the Air Regulator to 10-30 PSI, as shown on the Gauge (38). 3. Check the air connection for leaks and then disconnect the tool from the air source. Control Layout FIGURE 1 Pattern Control Knob (57) Trigger (78) Air Cap Set (45) Fluid Control Knob (67) Fluid Inlet Air Adjustment Knob (73) Air Inlet (80) For technical questions, please call 1-800-444-3353; SKU 93305 Page 6 Troubleshooting section at end of manual. IMPORTANT: Before using for the first time, the spray gun must be cleaned using a solvent based thinner. If not removed, the red oil used by the manufacturer for testing and corrosion protection may contaminate paint. IMPORTANT: The Spray Gun must be cleaned immediately after use. Improper cleaning is a common reason for the Spray Gun not to work. FIGURE 2 Fluid Flow Knob (11) Air Outlet Connector (36) Safety Valve (2) Fluid Outlet (39) Air Inlet Connector (36) Air Regulator (24) A Comparison: Conventional versus HVLP Spray Guns Because conventional spray guns require a much higher air cap pressure to atomize the paint than HVLP Spray Guns, conventional guns have lower transfer efficiencies and more overspray. This translates to a significant paint/material savings for HVLP guns, in addition to making them more environmentally friendly. To qualify as HVLP, the dynamic air pressure going in the Air Cap must be a maximum of 10 PSI. The lower the air pressure, the less bounce back and overspray. Note: Due to the viscosity of latex and other water-based paints, they are not recommended for use with this or other HVLP (High Volume Low Pressure) sprayers. See FIGURE 3 below. Conventional FIGURE 3 HVLP For technical questions, please call 1-800-444-3353; SKU 93305 Page 7 Troubleshooting section at end of manual. IMPORTANT: Before using for the first time, the spray gun must be cleaned using a solvent based thinner. If not removed, the red oil used by the manufacturer for testing and corrosion protection may contaminate paint. IMPORTANT: The Spray Gun must be cleaned immediately after use. Improper cleaning is a common reason for the Spray Gun not to work. Preparation Note: Proper paint material mixture helps to ensure less problems. Be sure to follow the manufacturer’s directions. Most materials will spray readily if they are thinned properly. General tips for Preparation: 1. Mix and thin the paint/materials thoroughly according to the manufacturer’s directions. 2. Carefully strain the paint/material through a paint strainer or piece of cheese cloth. 3. Remove (un-thread) the Cup (16) from the Unit. Fill the Cup (16) to approximately 3/4 full. Thread it back onto the unit. Connect the Fluid Hose (40) form the Fluid Outlet (39) to the Fluid Inlet on the Spray Gun. 4. Start the air compressor. 5. To adjust the spray pattern, set up a piece of scrap material to practice on. While practicing on the scrap material, check to see that the material you are spraying has the appropriate consistency. If it appears to thin, add a very small amount of thinner (not included). BE CAREFUL when thinning. Proceed slowly, adding very minimal amounts. NEVER exceed the manufacturer’s thinning recommendations. Fan direction and Pattern Adjustment Fan direction To change the direction of the fan from horizontal to vertical, loosen the Lock Ring and turn the Air Cap (45) 90 degrees. After the adjustment, tighten the Lock Ring by hand. See FIGURE 4 below. FIGURE 4 Horizontal Fan Vertical Fan Air Cap Lock Ring For technical questions, please call 1-800-444-3353; SKU 93305 Page 8 Troubleshooting section at end of manual. IMPORTANT: Before using for the first time, the spray gun must be cleaned using a solvent based thinner. If not removed, the red oil used by the manufacturer for testing and corrosion protection may contaminate paint. IMPORTANT: The Spray Gun must be cleaned immediately after use. Improper cleaning is a common reason for the Spray Gun not to work. Pattern Adjustment Warning!! Never exceed the Maximum Inlet PSI of 43 PSI. 1. Adjust the Gauge (38) pressure to 10-30 PSI using the Air Regulator (24). If you need to reduce the air pressure for specific areas, adjust the Air Adjustment Knob (73). 2. To set the pattern size specific to the job, use the Pattern Control Knob (57) (see FIGURE 1 on page 6). By turning it counterclockwise (all the way open), the pattern will flatten. Turn the Pattern Control Knob (57) clockwise for a round pattern. See FIGURE 5 below. Flat/Open Round/Closed FIGURE 5 3. Close the Fluid Control Knob (67) and fully open the Fluid Flow Knob (11). See FIGURE 1 on page 6. 4. After setting up a piece of scrap material, squeeze the Trigger (78) in short bursts while turning the Fluid Control Knob (67) counterclockwise and obse...

Herunterladen

Geben Sie zwei Ziffern: