Stimmen - , Durchschnittliche Bewertung: ( )

Anleitung GE, modell 00009246

Hersteller: GE
Dateigröße: 1.36 mb
Dateiname: 9ac3fcd8-ac80-4afd-8f5f-82da223e9ea2.pdf

Unterrichtssprache:

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

approved Nickel-Cadmium battery model 5-2459, which is compatible with this unit. 1. Locate battery and battery door which are packaged together inside a plastic bag and are separate from the handset. 2. Locate the battery compartment on the back of the handset. 3. Plug the battery pack cord into the jack inside the compartment. NOTE: To ensure proper battery installation, the connector is keyed and can be inserted only one way. 4. Insert the battery pack. 5. Close the battery compartment by pushing the door up until it snaps into place. 6. Place the handsets in the charging cradles. Allow handsets to charge for 16 hours prior to first use. If you don't properly charge the handsets, battery performance is compromised. 9 Installing the Phone Choose the best location to install your base and handset charge cradles. Your base and handset charge cradles should be placed on a level surface such as a desk or table top, or you may mount the base on a wall. Connecting the AC (Electrical) Power 1. On the base, plug the AC power adaptor cord into the power jack on the back of the base and the other into an electrical outlet. If desired, store the excess AC power adaptor line cord inside desktop pedestal. A CAUTION: To reduce risk of personal injury, fire, or damage use only the 5-2596 or 5-2732 (black), or 5-2625 or 5-2754 (gray color adaptor for white unit) power adaptor listed in the user's guide. This power adaptor is intended to be correctly orientated in a vertical or floor mount position. 2. Plug the handset charge cradle into an electrical outlet. NOTE: The charge indicator on the handset charge cradle turns on to indicate the handset battery is charging Connecting the Telephone Line On the base, plug one end of the straight telephone line cord into the jack on the back of the base and the other end into a modular wall telephone jack. Connecting the Corded Handset 1. Connect one end of the coiled handset cord to the jack on the side of the base. 2. Connect the other end of the coiled cord to the jack on the handset, then place the handset in the base cradle. 10 Wall Mounting the Base The base is packaged with the pedestal attached in desktop mode. To mount the base on the wall: 1. Turn the base over and remove the pedestal. 2. Rotate the pedestal a half turn, and align it with the bottom of the base. 3. Attach the pedestal by first inserting the tabs on the pedestal into the slots on the bottom of the base, and then push the pedestal down until it snaps into place. 4. Plug the telephone line cord into the jack marked PHONE LINE on the back of the base and the other end into a modular phone jack. 5. Feed the telephone line cord and AC power adaptor cord through the grooves on the pedestal to allow the unit to rest flat against the wall. 6. Slip the mounting holes on the pedestal over the wall plate posts and firmly slide the unit into place. (Wall plate not included.) 7. Remove the handset hook, turn it upside down, and put it back in the slot. You need to do this so the corded handset doesn't fall out of the base. 8. Place the corded handset in the base cradle. Answering System Set Up_ This section shows you how to set up your answering system to receive incoming calls. Before you begin the setup, you must turn on the answering system. • Press the ANSWERER ON/OFF button to turn the answering system on and off. The new messages indicator flashes when you have new messages. NOTE: The display shows ANSWERER OFF when the answering system is off. The default status is on. Voice Instructions If you need additional assistance, press the MEMO button on the base and follow the voice instructions. 11 Telephone Set Up_ There are twelve programmable menus available on the base: Language, Display Contrast, Rings to Answer, Security Code, Ringer Level, Ringer Tone, Tone/Pulse, Set Day, Set Time, Local Area Code, Link Cordless Handset, and Default Setting. There are five programmable menus available on the handset: Language, Local Area Code, Ringer Tone, Link Base, and Default Setting. NOTE: To exit the menu without making changes, press the *TONE/ EXIT button on the base or TONE*/exit on the handset. NOTE: You can press FLASH/PROGRAM at any time to go to the next menu item. NOTE: Changing menu settings on the handset will only change the settings on the handset, and changing menu settings on the base will only change the settings on the base. For example, if you change the language on the handset, it will not change language on the base. Language NOTE: This setting may be made on both the base and the cordless handset, independent of each other. 1. Press the FLASH/PROGRAM button until SET LANGUAGE 1ENG 2FRA 3ESP or 1ENG 2FRA 3ESP shows in the display. 1ENG is the default setting. NOTE: ENG stands for ENGLISH. FRA stands for French. ESP stands for SPANISH. 2. Press 1, 2, or 3 on the cordless handset or base touch-tone pad to enter your selection, or press the REVIEW or NE...