Stimmen - 4, Durchschnittliche Bewertung: 4.5 ( )

Hersteller: Black & Decker Dateigröße: 5.28 mb Dateiname: CO100,CO100WM,CO100B,CO951088.pdf Unterrichtssprache:

Note: If the height of your overhang molding is too tall to be accommodated by the number of spacers provided, you may call, toll-free, at 1-800-231-9786 to order additional spacers at no charge. Note: For spacer installation, you may require assistance in mounting in order to hold spacers in place while securing the appliance at the same time. If assistance is not available, use a small clamp to hold the spacers in place while you position the appliance. 15. Once spacers are set, hold appliance up and tighten screws to secure. Screw from inside the cabinet down. Note: Always tighten screws to ensure the appliance does not move or shake during operation. 16. Pull out cord from cord storage behind appliance and plug into standard electrical outlet. Extra cord can be fed back into storage or hung over cord management hook behind unit (see illustration F). Note: If you are connecting this appliance to the receptacle of another †SpaceMaker™ appliance such as the toaster oven or coffeemaker, make sure you can easily unplug the appliance following use. 17. Your †SpaceMaker™ appliance is now ready for use! K L How to Use This appliance is for household use only. OPENING A CAN 1. Lift piercing lever. 2. Tip can so that the rim is under the locating post, then push down on the piercing lever, making sure the cutter blade is inside the rim of the can (M). Note: Because of the hands-free feature, it is not necessary to hold the lever down or hold the can during cutting. However, you may have to support very tall or heavy cans. Tip: When the can is opened, the can opener will stop automatically. 3. To remove the can, hold it with one hand and raise the lever with the other. Caution: Avoid contact with the cut edges of the can or lids — they are sharp. During opening process, the design of your can opener will roll the rim of the can to prevent sharp edges; however, handle with caution and always handle cut lid with caution, as these edges are not rolled. 4. Carefully discard the lid from the magnet. Important Tips: • Do not use this can opener to open cans with a pull tab, peel-off foil seal, or rolling key or rimless cans. • Open frozen juices or foods in cardboard cans right from the freezer, while they are frozen. • Aluminum lids will not stick to the magnet. M USING THE KNIFE SHARPENER 1. For best results, sharpen the entire blade length in one continuous stroke. 2. Insert blade to be sharpened with the end of the blade closest to the handle on the knife into the sharpening slot. 3. Carefully press down on the blade and pull it toward you through the slot in one continuous stroke (N). Important: Do not saw knife back and forth to sharpen. Pull through the sharpener in one direction with a continuous, slow, even motion. Failure to do so may dull or damage your blade. 4. Repeat until desired sharpness is achieved. 5. Wash and dry knife before using again. Important Tips: • Use caution when washing and drying knives after sharpening. • Do not sharpen serrated blades, as this will smooth their edges. • Do not sharpen scissors. USING THE BOTTLE OPENER 1. Grasp the bottle and position cap above the lip on the back side of the bottle opener. 2. Tilt bottom of the bottle away from you to catch the cap on the lip and open the bottle (P). USING THE BAG CUTTER 1. Grasp the plastic or metal foil bag to be opened by one corner, with one hand holding the top edge and the other holding the side or bottom, depending on the size of the bag. 2. Position tightly pulled corner of bag against the cutter and pull firmly to the left to open the bag (Q). Note: Pulling a bag straight against the cutter will cut a line along the top of the bag; pulling at an angle will simply remove the corner. N P Q Care and Cleaning This product contains no user serviceable parts. Refer service to qualified service personnel. Important: Unplug the cord before cleaning the unit. REMOVING BLADE ASSEMBLY 1. Lift the piercing lever up as far as it will go (roughly 90°). 2. Carefully grip the blade assembly and pull it away from the can opener (R). 3. Wash in sudsy water by hand and dry thoroughly. Do not put the blade assembly in the dishwasher. 4. Before replacing the blade assembly, wipe the can opener body, knife sharpener and area around the geared wheel with a slightly damp cloth or sponge. REPLACING BLADE ASSEMBLY 1. Align key post on the blade assembly with key slot on the unit (S). 2. Push in blade assembly and turn clockwise until it locks into position (T). R S T INSTRUCCIONES IMPORTANTES DE SEGURIDAD Cuando se usa...

Herunterladen

Geben Sie zwei Ziffern: