Stimmen - 3, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
The heater will disengage at higher temperatures. IMPORTANT!Please refer to your Homeowners Guide for detailed instructions on the user keypad and optional remote control. Press the Power On/Off button to turn on the whirlpool. The whirlpool will start at medium flow. Increase or decrease the water flow by pressing either the up or down arrow buttons on the keypad. An indicator bar in the center of the keypad shows the water flow volume. Adjust each jet for optimum air/water mixture. Turn the jet trim clockwise to reduce the air flow, and counterclockwise to increase the air flow. Press the heater button to turn the heater off and back on. When illuminated, the indicator light shows that the water temperature will be maintained up to 104°F (40°C). Press the Power On/Off button a second time to turn the whirlpool off. NOTE:A built-in timer automatically stops the pump and motor after approximately 20 minutes of operation. Models with Neckjets Heater On/Off Decreases Flow Increases Flow Flow Mode Increases Flow Power On/Off Decreases Flow Lighted User Keypad (for whirlpools without neckjets) Lighted User Keypad (for whirlpools with neckjets) Heater On/Off Power On/Off Heater Indicator Light Indicator Bar - Shows water flow volume Activates Mode Selected Neckjet Mode - Adjust Pulse Turn the jet trim clockwise to decrease the flow. Turn the jet trim counterclockwise to increase the flow. 1019749-2-M 14 Kohler Co. Operating Sequence (cont.) NOTE: A built-in heater automatically helps to maintain the water temperature when the whirlpool is running, as long as the water temperature does not exceed 104°F (40°C). The heater will disengage at higher temperatures. IMPORTANT! Please refer to your Homeowners Guide for detailed instructions on the user keypad and remote control. Press Power to turn on the whirlpool. The whirlpool will start at medium flow. Increase or decrease the water flow by pressing either the up or down arrow buttons on the keypad. An indicator bar in the center of the keypad shows the water flow volume. Adjust each jet for optimum air/water mixture. Turn the jet trim clockwise to reduce the air flow, and counterclockwise to increase the air flow. Make sure the slip cover is in place on the pillow, and the pillow is attached to the neckjet body. With the whirlpool operating, rotate the outer ring until the neckjet icon is flashing. Press .OK. to activate the neckjets. The neckjet pulsing action will start at medium speed. Increase or decrease the neckjet pulsing action by pressing either the up or down arrow buttons on the keypad. To activate or deactivate different modes while the neckjets are operating, rotate the outer ring until the desired mode is flashing and press .OK.. (Example: To turn the heater off, rotate the dial until the heater icon is flashing and press .OK.). Press .OK. while the neckjet mode is flashing to turn off the neckjets. Press the Power On/Off button a second time to turn the whirlpool off. NOTE: A built-in timer automatically stops the pump and motor after approximately 20 minutes of operation. 19. Troubleshooting Procedures This troubleshooting guide is for general aid only. A KOHLER Authorized Service Representative or qualified electrician should correct all electrical problems. For warranty service, contact your dealer or wholesale distributor. Troubleshooting the Whirlpool System Symptoms Probable Causes Recommended Action 1. User keypad does not illuminate when power button is pressed or outer ring is rotated. A. No power to control. B. GFCI or RCD tripped. C. Wiring harness from user keypad to control is loose, disconnected or damaged. D. User keypad does not work. E. Control does not work. A. Check wiring and connect power. B. Reset GFCI ...
Dieses Handbuch ist für folgende Modelle:Andere Home Zubehör - K-1014 (2.57 mb)
Andere Home Zubehör - K-1110 (2.57 mb)
Andere Home Zubehör - K-1158 (2.57 mb)
Andere Home Zubehör - K-1170 (2.57 mb)