Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
8. Pump does not automatically stop after 22 minutes. A. 20-minute timer inadvertently disabled. A. See service manual. 9. Pump won’t turn off when the power button on user keypad is pressed. A. User keypad does not work. B. Control does not work. A. Replace user keypad. B. Replace control. 10. Pump operates but variable speed feature does not work. A. Motor/pump does not work. B. Control does not work. A. Replace motor/pump. B. Replace control. 11. Bath water cools while pump is operating. A. Water temperature above 104°F (40°C). B. Heater is turned off on user keypad. C. Wiring from heater to control is loose, disconnected or damaged. D. Heater does not work. E. Control does not work. A. Allow bath water to cool. B. Turn heater on. C. Check wiring for proper connections. D. Replace heater. E. Replace control. 12. Noisy operation. A. Pump banding straps have not been cut. A. Cut pump banding straps with tin snips. 1019749-2-M 16 Kohler Co. Troubleshooting Procedures (cont.) Symptoms Probable Causes Recommended Action B. Dry or dislodged jet O-ring (squeal). B. Remove jet, replace and lubricate O-ring, and reinstall jet. 13. Remote control (if equipped) does not work. A. Batteries improperly installed or dead. B. Antenna on wiring harness is damaged. C. Remote control not programmed correctly. D. Remote control does not work. E. Control does not work. A. Replace batteries. B. Replace wiring harness. C. See homeowners guide or service manual. D. Replace remote control. E. Replace control. Troubleshooting the Neckjet System Symptoms Probable Causes Recommended Action 14. Keypad does not respond when neckjet mode is selected. A. User keypad does not work. A. Replace user keypad. 15. Pump operates but neckjets do not turn on. Indicator bar on user keypad is flashing. A. Pillow is not installed. B. Reed switch does not work. C. Wiring harness from neckjet to control is loose, disconnected or damaged. A. Make sure the pillow is properly attached to the neckjet body. B. Check reed switch wiring and replace if necessary. C. Check wiring for proper connections. Replace wiring harness if necessary. 16. Pump operates but neckjets do not turn on. Indicator bar on user keypad is NOT flashing. A. Neckjet line is blocked. B. Wiring harness from neckjet to control is loose, disconnected or damaged. C. Butterfly valve does not work. D. Control does not work. A. Disconnect neckjet hoses and remove blockage. B. Check wiring for proper connections. Replace wiring harness if necessary. C. Replace butterfly valve. D. Replace control. 17. Water flows from neckjets, but neckjets do not pulse. A. Wiring harness from neckjet pulse cannister to control is loose, disconnected or damaged. B. Pulse cannister does not work. C. Control does not work. A. Check wiring for proper connections. Replace wiring harness if necessary. B. Replace pulse cannister. C. Replace control. Kohler Co. 17 1019749-2-M Guide d’installation Baignoire a hydromassage encastree Informations importantes AVERTISSEMENT: Lors de l’utilisation des produits electriques, des precautions de base doivent toujours etre observees, incluant ce qui suit: DANGER: Risque d’electrocution. Raccorder uniquement a des circuits proteges par un Disjoncteur de Fuite de Terre (GFCI) ou un appareil de courant residuel (RCD). Les materiaux de construction et le cablage devraient etre achemines loin du corps de la pompe et des autres composants qui degagent de la chaleur de l’unite. Installer de facon a permettre l’acces pour l’entretien. Installer l’unite conformement au Code canadien de l’electricite, 1ere partie. Un connecteur a pression pour cables marque .Terre/Masse. est fourni dans le compartiment de cablage. Afin de reduire les risques de choc electrique...
Dieses Handbuch ist für folgende Modelle:Andere Home Zubehör - K-1014 (2.57 mb)
Andere Home Zubehör - K-1110 (2.57 mb)
Andere Home Zubehör - K-1158 (2.57 mb)
Andere Home Zubehör - K-1170 (2.57 mb)