Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Detach the pillow by lifting it off the whirlpool surface. Pump Wiring Harness Rubber Isolation Feet Control Cut the pump banding str aps . Moisten the back of the pillow and firmly press the suction cups against the whirlpool surface. Optional Pillo w- F or Models Without Nec kjets Kohler Co. 9 1019749-2-M 9. Make Electrical Connections NOTE: The product model number is printed on a label on the pump side of the whirlpool bath. This label also identifies the electrical rating of the product. All whirlpools come equipped with a wiring junction box and are designed to operate between 220 V and 240 V at either 50 Hz or 60 Hz. WARNING: Risk of electrical shock. Make sure the power has been disconnected before performing the following procedures. Refer to the “Important Information” section. WARNING: Risk of electrical shock. To reduce the risk of electrical shock, connect the pump to a properly grounded Ground-Fault Circuit-Interrupter (GFCI) or Residual Current Device (RCD). This will provide additional protection against line-to-ground shock hazard. A 220-240 V, 20 A, 50/60 Hz dedicated circuit is required. IMPORTANT! The load neutral is not used. There should be no connection to the load neutral terminal on the Ground-Fault Circuit-Interrupter (GFCI) breaker. The green wire with the yellow stripe is the equipment ground and needs to be connected to the neutral bus in the main circuit breaker box. The whirlpool bath control and system have been pre-wired at the factory. A licensed electrician should make a routine service connection to the junction box. Connect service to the junction box. The junction box contains blue, brown, and green with a yellow stripe colored wires. Follow local electrical codes. Bond in accordance with national and local codes. A wiring harness has been pre-wired at the factory, allowing communication between the keypad, all features, and the control. No additional wiring is required, but ensure that all wires are securely fastened. NOTE: Your wiring harness included an antenna for the optional remote control. Do not alter or damage this antenna during installation. Heater (models may vary) T-style (shown) or In-line (not shown) Heater Electrical Cord Wiring Harness Junction Box Control Pump Electrical Cord From Control Brown (L2) * Connections to be Made at the Circuit Breaker S/N * Equipment Ground Wire Connectors Neutral Bus (In Breaker Box) 120/240 VAC Source Typical Two-Pole Circuit Breaker with GFCI * Line Neutral (White Curly Wire) Typical Wiring Connection for North America Ground (Green with Yellow Stripes) *L1 No Connection (Load Neutral) Field Wiring (From Junction Box to GFCI Breaker) Electrician to provide suitable strain relief cable. Wire Connector Blue (L1) *L2 240 V 120 V 240 V 120 V Breaker Box N L1 L2 Bond in accordance with national and local codes. Open bonding lugs are located at the top of the junction box. 1019749-2-M 10 Kohler Co. 10. Install the Whirlpool Trim Kit Install the whirlpool trim kit according to the instructions packed with the trim kit. Pay particular attention to the jet installation steps below -they are very important and are included here to help you obtain smooth, trouble-free jet operation. NOTE:The jet O-ring must be correctly positioned, must be lubricated, and must be in good condition to permit easy rotation and proper operation of the jet. Install the O-ring onto the firstshoulderof the jet. Lubricate the O-ring with silicone lubricant to prevent noisy operation of the jet. Carefully insert the jet into the housing, and lightly push and rotate the jet until it snaps into position. Donotforcethejet. NOTE:When installed correctly, the jet should turn smoothly both clockwise and counterclockwise. 11. Install th...
Dieses Handbuch ist für folgende Modelle:Andere Home Zubehör - K-1014 (2.57 mb)
Andere Home Zubehör - K-1110 (2.57 mb)
Andere Home Zubehör - K-1158 (2.57 mb)
Andere Home Zubehör - K-1170 (2.57 mb)