Stimmen - 2, Durchschnittliche Bewertung: 4 ( )

Hersteller: Axor Dateigröße: 131.56 kb Dateiname: bc3df628-a323-4fda-b1b5-b9bdaf920a6a.pdf Unterrichtssprache:

Certified to comply with ANSI A112.18.1M U.S. Patent No. 5,819,789 DRAIN STOPPER CLIP EXTENSION TAILPIECE AERATOR COUPLING NUT O-RING CONVENTIONAL SPOUT LESS POP-UP 6802 SERIES WRENCH LIFT ROD 6801 SERIES HERITAGE SPOUT W/POP-UP RUBBER WASHER RETAINER LOCKNUT TUBE & TEE ASSEMBLY THUMBSCREW HANDLE SCREW CARTRIDGE ESCUTCHEON RUBBER RING RUBBER WASHER BRASS WASHER LOCKNUT VALVE ASSEMBLY ACTUATOR ROD COUPLING GASKET LOCKNUT WASHER DRAIN PLUG GASKET O-RING SCREW RUBBER GASKET GOOSENECK SPOUT WITH POP-UP 6831 SERIES HERITAGE SERIES SEAL COMPRESSION NUT FRICTION RING M34375C P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c . C Ame r i c a n S t a n d a r d I n c . 1 9 9 9 HOTLINE FOR HELP For toll-free information and answers to your questions, call: 1 (800) 223-0068 Weekdays 8:00 a.m. to 7:00 p.m. Eastern Time Saturdays 8:00 a.m. to 4:00 p.m. Eastern Time Turn off hot and cold water supplies before beginning. CAUTION VALVE INSTALLATION DRAIN INSTALLATION SERVICE 1 6 2 4 LEDGE RUBBER WASHER BRASS WASHER LOCKNUT VALVE BODY 5/16'' MIN. ESCUTCHEON RUBBER RING LOCKNUT SPOUT EXTENSION CLIP CLIP LIFT ROD EXTENSION THUMBSCREW ACTUATOR ROD CARTRIDGE SCREEN SPRING CLIP STOP WASHER RETAINER RUBBER WASHER RUBBER GASKET SINK Insert BASE or SPOUT shank through center hole of SINK, making sure RUBBER GASKET is properly positioned. SPOUT OR BASE ASSEMBLY Assemble RUBBER WASHER, RETAINER, and LOCKNUT onto threads of SPOUT from underside of SINK. Insert LIFT ROD through SPOUT (or BASE) and slot of RETAINER. Align SPOUT and tighten LOCKNUT. Be sure slot in BRASS WASHER is positioned to the rear as shown. Prepare TUBE and TEE ASSEMBLY to fit available VALVE location. If necessary, cut and/or bend TUBING carefully. Make sure tube bend is close to the TEE so that it will not effect the compression joint at the VALVE. Place RUBBER RING into ESCUTCHEON and screw ESCUTCHEON onto VALVE BODY until snug against internal stop. Tighten LOCKNUT to secure VALVE position. Attach COUPLING to TEE and tighten. ACTUATOR ROD TAIL PIECE TEST INSTALLED FAUCET5 Remove AERATOR. With handle in OFF position, turn on water supplies and check all connections for leaks. Operate both handles to flush water lines thoroughly. Check spout mounting and hose connections for leaks. Operate LIFT ROD and check DRAIN for leaks. Turn handles into OFF position and replace AERATOR. Apply a bead of PUTTY around the underside of DRAIN PLUG flange and insert DRAIN PLUG into SINK drain hole. Hold DRAIN PLUG firmly to prevent turning, and assemble the GASKET, WASHER, and LOCKNUT from underneath the SINK. Insert GASKET into COUPLING and attach COUPLING to DRAIN PLUG. Align COUPLING so that the ACTUATOR ROD faces rear of SINK and tighten LOCKNUT to secure position. Unscrew ACTUATOR NUT and withdraw the ACTUATOR ROD. Drop STOPPER into DRAIN PLUG with the OFFSET SQUARE SLOT in line with ACTUATOR ROD opening. Reassemble ACTUATOR ROD. Make sure ROD is insi...

Herunterladen

Geben Sie zwei Ziffern: