Stimmen - 2, Durchschnittliche Bewertung: 4.5 ( )

Hersteller: Hoshizaki Dateigröße: 2.87 mb Dateiname: Unterrichtssprache:

°F (°C) 70 80 90 100 *23 (-5) 23 (-5) 23 (-5) 23 (-5) 26 (-4) 26 (-4) 26 (-4) *26 (-4) 28 (-3) 28 (-3) 28 (-3) *28 (-3) HEAD PRESSURE PSIG (kg/cm2G) 70 80 90 100 *230 (16.2) 230 (16.2) 230 (16.2) 264 (18.5) 264 (18.5) 264 (18.5) 297 (20.9) *297 (20.9) 297 (20.9) 335 (23.5) 335 (23.5) *335 (23.5) SUCTION PRESSURE PSIG (kg/cm2G) 70 80 90 100 *33 (2.3) 33 (2.3) 33 (2.3) 35 (2.5) 35 (2.5) 35 (2.5) 37 (2.6) *37 (2.6) 37 (2.6) 43 (3.0) 43 (3.0) *43 (3.0) TOTAL HEAT OF REJECTION 6300 BTU/h (AT 90°F /WT 70°F) Note: 1. The data without *marks should be used for reference only. . We reserve the right to make changes in specifications and design without prior notice. 34 2. DCM-500BWH(-OS) APPROXIMATE ICE PRODUCTION PER 24 HR. lbs./day ( l/day) Ambient Temp. (°F) Water Temp. (°F) 50 70 90 70 80 90 100 * 567 257 549 249 539 244 529 240 519 235 509 231 500 227 * 495 224 481 218 472 214 464 210 * 428 194 APPROXIMATE ELECTRIC CONSUMPTION watts 70 80 90 100 * 976 -967 -991 -976 -967 -991 -976 -* 967 -991 -976 -967 -* 991 -APPROXIMATE WATER CONSUMPTION PER 24 HR. (TOTAL) gal. / day (kl/day) 70 80 90 100 * 111 0.51 130 0.59 194 0.88 111 0.50 130 0.59 198 0.90 110 0.50 * 130 0.59 203 0.92 110 0.50 132 0.60 * 214 0.97 EVAPORATOR OUTLET TEMP. °F (°C) 70 80 90 100 * 19 -7 19 -7 19 -7 19 -7 19 -7 19 -7 19 -7 * 19 -7 19 -7 19 -7 19 -7 * 19 -7 HEAD PRESSURE PSIG (kg/cm2G) 70 80 90 100 * 266 18.7 267 18.8 270 19.0 266 18.7 267 18.8 270 19.0 266 18.7 * 267 18.8 270 19.0 266 18.7 267 18.8 * 270 19.0 SUCTION PRESSURE PSIG (kg/cm2G) 70 80 90 100 * 44 3.1 44 3.1 47 3.3 44 3.1 44 3.1 47 3.3 44 3.1 * 44 3.1 47 3.3 44 3.1 44 3.1 * 47 3.3 WATER FLOW FOR CONDENSER 21 gal/h (AT 90°F /WT 70°F) PRESSURE DROP OF COOLING WATER LINE Less than 7 PSIG HEAT OF REJECTION FROM CONDENSER 5438 BTU/h (AT 90°F /WT 70°F) HEAT OF REJECTION FROM COMPRESSOR 1104 BTU/h (AT 90°F /WT 70°F) Note: 1. The data without *marks should be used for reference only. . We reserve the right to make changes in specifications and design without prior notice. 35 IV. Service Diagnosis A. Diagnostic Procedure This diagnostic procedure is a sequence check that allows you to diagnose the electrical system and components. Before proceeding, check for correct installation, adequate water supply (minimum of 10 PSIG, maximum of 113 PSIG) and proper voltage per unit nameplate. Always choose a white neutral wire to establish a good neutral connection when checking voltages. LEDs on the control board correspond to the components as they energize. 1) Move the control switch to the "OFF" position, then turn off the power supply. Remove the upper and lower front panels. Confirm the power switch is in the "ON" position and the door switch is engaged. ) Turn on the power supply, then move the control switch to the "ICE" position. The "POWER" LED is on. The "POWER" LED will not come on if the door switch is not engaged. 3) Fill Cycle – The inlet water valve energizes. The reservoir fills. The lower float switch closes. Nothing occurs at this time. The reservoir continues to fill until the upper float switch closes, energizing the water control relay, which closes the low water safety circuit and de-energizes the inlet water valve. Diagnosis: Check that the inlet water valve fills the reservoir. If not, check for water supply line shut-off valve closed, clogged water filters, clogged inlet water valve screen, power circuit to the inlet water valve (power switch, door switch, power protect relay contacts, transformer, fuses, high pressure switch, bin control, control switch, float switch, water control relay contacts), and the coil on the inlet water valve. Check that the inlet water valve shuts off when the upper float switch closes. If not, check the float switch, water control relay, and inlet water valve. 4) Ice Purge Cycle – "GM" LED is on (60 second short cycle protection). The 60 second timer starts, the gear motor protect relay and gear motor energize. Diagnosis: Check that the gear motor starts. If not, check that the water control relay is energized (inlet water valve should be closed). Check the low water safety circuit on the water control relay (terminals 4 and 6), check for 115/1 0V at the K1 connector "COM" terminal to neutral and "NO" terminal to neutral on the control board (see wiring diagram), check the gear motor fuse (overload protector), thermal protector, gear motor capacitor, and motor windings. If the gear motor starts, but the auger does not turn, check the gear motor coupling between the auger and the gear motor. If the compressor starts at the same time the gear motor starts, check the X compressor relay on the control board. 5) Freeze Cycle – "GM", "COMP" LED are on. The compressor and fan motor energize, the gear motor protect relay, gear motor, and water control relay remain energized. Ice production begins 4 to 6 minutes after the compressor and fan motor start depending on ambient and water temperature conditions. Diagnosis: Check that the compressor and fan motor a...

Herunterladen

Geben Sie zwei Ziffern: