Stimmen - 4, Durchschnittliche Bewertung: 4.3 ( )

Hersteller: Cleveland Range Dateigröße: 2.62 mb Dateiname: Unterrichtssprache:

NUT ..................................................2 PNEUMATIC HOSE 1/4 I.D. X 31" L ..................................1 PNEUMATIC HOSE 1/4 I.D. X 12 1/2” L ...............................1 FLAT WASHER #10, ZINC PLATED...................................2 AIR SOLENOID ASSEMBLY ........................................1 GROMMET ..................................................... 2 1/4-20 NUT S.S..................................................2 FLAT WASHER 1/4 DIA., ZINC PLATED ...............................2 SIDE BOX -TILT MECHANISM & SWITCHES GAS CONNECTION SEE PNEUMATIC COMPONENTS DRAWING ITEM NO. PART NO. 1. KE50579-1 FA00012 KE50580 2. KE603208-4 3. KE51730 4. KE54531 5.* KE54530 6.* KE54529 7.* KE54532 8. KE01889 DESCRIPTION CIRCUIT BREAKER............................... "O" RING, CIRCUIT BREAKER ...................... WATER RESISTANT BOOT ......................... TILT SWITCH OPERATOR.......................... TILT SHAFT BEARING............................. AGITATOR STOP................................. AGITATOR START ................................ POWER ON/OFF SWITCH.......................... SPEED CONTROL ................................ MICRO SWITCH TRIGGER/SEGMENT GEAR WELDMENT QTY. 9. FA10772 SOCKET HD. CAP SCREW................. 10. FA20048 JAM NUT............................... 11. FA95007-4 RETAINING RING ........................ 12. FA95055-1 SQUARE KEY ........................... 13. FA19201 HEX SOCKET SET SCREW 3/8-24 ........... 14. KE54644 TILT SHAFT, MANUAL TILT................. KE52836-2 TILT SHAFT, POWER TILT.................. 15. KE50315 WORM................................. 16. FA95005 TENSION PIN ........................... 17. KE52193-1 THRUST BEARING SPACER................ 18. KE52192 THRUST WASHER........................ 19. KE52191 ROLLER BEARING ....................... 20. FA30088 WASHER ............................... 21. FA95008 JAM NUTS.............................. 22. KE50582 CPLG. ONTARIO BELTING #G-100 5/8 BORE . . 23. FA95055-6 SQUARE KEY 3/16 X 3/16 X 1" LG........... 24. KE50583 RUBBER INSERT, ONTARIO BELTING “BUNA N 25. KE52832-1 MOTOR "BODINE" ........................ 26. FA10487 HEX HD SCREW 1/4-20 X 1" LG............. 27. FA31008 SPLIT LOCKWASHER 1/4" DIA.............. 28. FA20026 HEX NUT 1/4 - 20 ........................ 29. KE50473 GROUND LUG .......................... 30. FO1518-1 GAS SHUT-OFF VALVE .................... 31. KE02053 COMBINATION GAS VALVE NATURAL GAS . . . 32. FI05223-1 SPECIAL NIPPLE......................... 33. FI05222 SWIVEL ELBOW ......................... 34. FI05231 FLUSH BUSHING 3/4M TO1/2F ............. 35. FI05226-11 NIPPLE 1/2 X 10" LG...................... 36. KE51007 MICRO SWITCH ......................... 37. FA10139 MACHINE SCREW #6-32 X 1" LG............ 38. KE50498 MICRO SWITCH INSULATION .............. 39. FA32004 TOOTH LOCK WASHER #6 ................ 40. KE603208-7 CONTACT SECTION HOLDER (LATCH)....... 41. KE603208-9 CONTACT BLOCK ....................... 42. KE50581 BRIDGE RECTIFIER ...................... 43. KE54535 EDGE CONNECTOR (11 PIN)............... 44. KE50753-10 RELAY ................................. 45. KE54491 LID FOR GEARBOX ...................... 46. KE53599-8 GASKET ............................... 47. KE53599-9 GASKET ............................... 48. FA95062 PAN HD. PHILLIPS SCREW ................ 49. FA95074 NYLON ANCHOR NUT .................... 50. FA19177 HEX SOCKET SET SCREW 5/16-24 X 1" ...... 51. FA20047 JAM NUT 5/16-24 ........................ 52. KE54606 GAS VALVE LOCKWASHER ................ 53. KE003209-9 SWITCH, JOG TO OPEN AIR VALVE ......... 54.* KE003209-6 SWITCH, FILL INTERRUPT................. 55. * KE003209-2 SWITCH, HOT/COLD SELECTION ........... 56.* KE003209-3 SWITCH, FILL CYCLE..................... 2 2 1 1 1 1 1 1 1 2 4 2 2 2 2 1 1 1 4 4 4 1 1 1 1 1 1 1 2 4 2 4 1 4 1 2 2 1 2 2 4 * SWITCHES MAY BE LOCATED ON REMOTE CONTROL PANEL MAINTENANCE INSPECTION AND MAINTENANCE CHECKLIST Cleveland Range equipment requires little preventative maintenance. We do however provide the following chart as a guide line for inspection and maintenance to keep your unit functioning at 100%. MONTHLY INSPECTION □ Inspect all switches for damage. Replace rubber boots or switches as required. □ Check that the automatic dump valve works fully and smoothly and no air leaks are evident. □ Check that the 3 way regulator shuts off the incoming air and completely vacates the air from the air hose to the metering filling station. □ Tilt kettle and check for smooth operation in both directions. □ Inspect gear and worm assembly in gear box for play - tighten Allen screws if required. □ Inspect gasket material on covers for integrity □ Check spring assist covers for tightness to handle and insure spring is holding cover up - adjust if required. Refer to HINGE ADJUSTMENT INSTRUCTIONS. □ Wh...

Herunterladen

Geben Sie zwei Ziffern: