These warnings have been provided in the interest of safety. You MUST read them carefully before installing or using the appliance. If you are unsure of the meanings of these warnings contact the John Lewis branch from which you purchased the appliance. In the interest of your safety and to ensure the correct use, before installing and first using the appliance, read this user manual carefully, including its hints and warnings. To avoid unnecessary mistakes and accidents, it is important to ensu

Make sure that the connection is correct. The water inlet hose is damaged. Make sure that the water inlet hose has no damages. The appliance does not drain the water. There is a blockage in the sink spigot. Clean the sink spigot. The connection of the water drain hose is not correct. Make sure that the connection is correct. The water drain hose is damaged. Make sure that the water drain hose has no damages. The anti-flood device is on. Close the water tap and contact our extended warranty admin

supply. 28 29 Water drain connection The end of the drain hose can be connected in the following ways: 1. To the sink outlet spigot, securing it to the underside of the work surface. This will prevent waste water from the sink running into the machine. 2. To a stand pipe provided with venthole, minimum internal diameter 4 cm. The waste connection must be at a height of between 30 cm (minimum) and 100 cm (maximum) from the bottom of the dishwasher. The drain hose can face either to the right or l

The start of the programme or the countdown of the delay start will occur only after the closure of the door. Until then it is possible to modify the settings. 1. Check that the baskets have been loaded correctly and that the spray arms are free to rotate. 2. Check that the water tap is opened. 3. Press the On/Off button. The dishwasher must be in setting mode. 4. Press one of the two programme buttons to select a washing programme. When a programme is selected the corresponding programme light

These warnings have been provided in the interest of safety. You MUST read them carefully before installing or using the appliance. If you are unsure of the meanings of these warnings contact the John Lewis branch from which you purchased the appliance. In the interest of your safety and to ensure the correct use, before installing and first using the appliance, read this user manual carefully, including its hints and warnings. To avoid unnecessary mistakes and accidents, it is important to ensu

Indicator lights Salt 1) Comes on when the special salt has run out. Rinse aid 1) Comes on when the rinse aid has run out. Indicator lights Multi tab Indicates the activation/ deactivation of the Multi tab function (See 'Multi tab function'). 1) The salt and rinse aid indicator lights are never on while a washing programme is running even if filling with salt and/or rinse aid is necessary. 7 The digital display The digital display indicates: • The level of hardness to which the water softener is

The dose is factory set in position 4. Increase the dose if there are drops of water or lime spots on the dishes after washing. Reduce it if there are sticky whitish streaks on the dishes or a bluish film on glassware or knife blades. 14 Daily use • Check if it's necessary to refill with dishwasher salt or rinse aid. • Open the door and slide out the baskets to load the dishes. • Load cutlery and dishes into the dishwasher. • Fill with dishwasher detergent. • Select a wash programme suitable for

Fill the salt container and the rinse aid dispenser. 2. Adjust manually and electronically the water softener to the highest level. 3. Start a washing programme without dishes. 4. When the washing programme is completed, adjust the water softener to the water hardness in your area. 5. Adjust the rinse aid dosage. 17 Select and start a washing programme Starting the washing programme 1. Switch on the appliance. Make sure that the appliance is in setting mode. 2. Select a washing programme. Refer

If the appliance is partially loaded and the dishes lightly soiled, the "prewash", "main wash", and "rinse" phases of the programme are shorter and the water consumption level is lower. If the appliance is fully loaded and the dishes heavily soiled, the "prewash", "main wash", and "rinse" phases of the programme are longer and the water consumption level is higher. During the "Automatic" programme the temperature of the main wash water is also automatically adjusted between 50°C and 65°C dependi

2. To a stand pipe provided with vent-hole, minimum internal diameter 4 cm. The waste connection must be at a height of between 30 cm (minimum) and 100 cm (maximum) from the bottom of the dishwasher. The drain hose can face either to the right or left of the dishwasher Ensure the hose is not bent or squashed as this could prevent or slow down the discharge of water. The sink plug must not be in place when the machine is draining as this could cause the water to syphon back into the machine. If y