1 4 0502645 1/8" Hose Barb........................................................................... 2 5 0502666 1/8" Hose.................................................................................... AR 6 0300918 Plumbing Clamp......................................................................... 1 7 0501501 Lock Washer, 1/4"...................................................................... 2 8 0501539 Nut, 1/4-20 ...................................................................
low ..................Hot water supply min. 145°F/66°C Water on floor around Pump seal leaking ...............................Replace machine Rinse drain in wash area plugged .......Clear obstruction, clean machine Wash return screen in detergent..........Clean tank plugged Drain screen under detergent .............Clean tank plugged Main drain plugged .............................Clean Detergent tank covers are not .............Position all top covers to completely cover positioned properly cau
2. Start the washer with rocker switch located on the front of the machine. Take a sample from the final rinse spray tube to check sanitizer level. 3. To increase the volume of sanitizer, turn the adjustment screw clockwise. 4. To decrease the volume of sanitizer, turn the adjustment screw counter-clockwise. NOTE: If Iodopher is being used as a sanitizer, it is not necessary to use a separate rinse agent. To turn rinse agent injector “OFF” in this case, turn the adjustment screw counter-clockwis
Mixing will cause hazardous gases to form. Skin contact with deliming solutions can cause severe irritation and possible chemical burns. Consult your chemical supplier for specific safety precautions. 1. Remove the sanitizer tube from the container. Place the tube into a container of hot water. 2. Depress and hold the SANITIZER prime switch (located on the front panel) until all sanitizer has been purged from the hoses. 3. Close the door and depress the door latch. Complete two operating cycles
Kit is supplied with new data plate for machine. Factory will supply jumper settings for element at time of installation. REPLACEMENT PARTS 1 23 5 6 11 12 13 14 15 14 10 789 2 2 WATERCONNECTION TO FILL 4 00049 Figure 7 — Water Inlet Piping (HTN, LT Only) REPLACEMENT PARTS WATER INLET PIPING (HTN, LT ONLY) Fig. 7 Part Description Qty Item No. No. 1 0503718 Foot, adjustable .......................................................................... 4 2 0503679 Clamp, hose...........................
1 7 0710593 Wash Arm, Upper....................................................................... 1 8 0505042 Pivot, Upper Wash Arm ............................................................. 1 9 0308783 Retainer, Upper Pivot ................................................................. 1 10 0501563 Screw, #8 x 3/8 Truss Head........................................................ 2 11 0501684 Nut, Spray Arm Lock................................................................. 1 12 070504
d. Release the toggle switch to stop the water flow. e. You have complete the booster priming process. NOTE: Push the Installation and Service toggle switch to the ON position. Electrical power is now supplied to the machine. ! WARNING: Failure to prime the booster may cause damage to the booster elements and other electrical components and will void the warranty, 4. After plumbing and electrical connections are completed, check the machine for water leaks by depressing the ON/FILL/OFF/DRAIN to
Service Road Jordan Station, Ontario, Canada L0R 1S0 Moyer Diebel, Ltd. 905/562-4195 Fax: 905/562-4618 Complete the information below so it will be available for quick reference. Model Number __________________________ Serial Number ________________________ Voltage and Phase ______________________________________________________________ Moyer Diebel Parts Distributor _______________________________ Phone _____________ (if applicable) Moyer Diebel Service Agency ________________________________ P
1. Immediately after unpacking your machine, inspect for any shipping damage. If damage is found, save the packing material and contact the carrier immediately. 2. Remove the dishwasher from the skid. Adjust the feet if required, then move the machine to its permanent location. 3. Level the machine (if required) by placing a level on the top of the machine and adjusting the feet. Level the machine front-to-back and side-to-side. ! CAUTION: After locating your machine, the installation must meet
1 2 0308610 Bracket, Detergent/Sanitizer Pumps (Rinse Aid)....................... 1 3 N/A Screw, M4 x 35mm Hex Head ................................................... 4 4 0501412 Screw, 10-32 x 3/8" Lg. Truss Head........................................... 2 5 N/A Housing, Pump........................................................................... 1 6 0501497 Washer, Lock #8 Split ................................................................ 2 7 0504822 Screw,8-32 x 1/2" Lg. Pan Head ...