Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
This plug will only fit into a matching polarized AC outlet. This is a safety feature to reduce the possibility of electric shock. If this plug will not fit in your AC outlet, you probably have an outdated non-polarized outlet. You should have your out-dated outlet changed by a qualified, licensed electrician. Do not file the wide blade on the plug, or use an adaptor to make the plug fit onto your outlet. This defeats the safety feature and could expose you to electric shock. RADIO OPERATION 1. Slide the FUNCTION SWITCH to “FM” or “AM” as desired. The POWER Indicator will light. 2. Rotate the TUNING CONTROL to your desired radio station according to the DIAL SCALE on the unit. 3. Rotate the VOLUME CONTROL to adjust to the desired output level. 4. To turn off the radio, slide the FUNCTION SWITCH to “OFF”. The POWER Indicator will go off. TIPS FOR BEST RECEPTION AM – The AM antenna is located inside the cabinet of the unit. If AM reception is weak, change the position of unit until the internal antenna picks up the strongest signal. FM – If a stereo broadcast program is being received, the FM STEREO INDCATOR will light. During FM or FM Stereo reception, always keep the FM TELESCOPIC ANTENNA fully extended for best performance. However, if FM reception is weak, try repositioning the unit near an open window until you get the best reception. CD OPERATION NOTE: THIS UNIT NOT ONLY PLAYS COMMERCIAL COMPACT DISCS BUT ALSO SELF-COMPILED CD-RW DISCS. . Because of non-standardized format definition/production of CD-R/RW, playback quality & performance is not guaranteed. . Manufacturer is not responsible for the playability of CD-R/RW due to recording conditions such as PC performance, writing software, media properties etc. . Do not attach a label or seal to either side of the CD-R/RW disc. It may cause a malfunction. PLAY MODE 1. Slide the FUNCTION SWITCH to the “CD” position. The POWER INDICATOR will light. 2. Open the CD DOOR, load a CD with the label side facing upward and then close the CD door. 3. A few seconds later the total number of tracks on the CD will appear on the LED DISPLAY. 4. Press the PLAY/PAUSE BUTTON to start playing the CD from the first track. The PLAY/PROG INDICATOR will light steadily. 5. While playing, press the PLAY/PAUSE BUTTON once to pause, the LED DISPLAY will flash. Press PLAY/PAUSE BUTTON again to resume playing. 6. Adjust the VOLUME CONTROL to the desired volume level. 7. Press STOP BUTTON to stop playing. 8. To turn off the CD player, slide the FUNCTION SWITCH to “OFF”. The POWER INDICATOR will go off. NOTE: If skipping occurs during CD play, try turning the volume down. Do not open the CD DOOR when a CD is playing. REPEAT MODE Repeat 1 When the REPEAT BUTTON is pressed once, the REPEAT INDICATOR will light and blink continuously. The current track will be repeated until it is interrupted. Repeat All When the REPEAT BUTTON is pressed twice, the REPEAT INDICATOR will light steadily. The whole disc will be played continuously. To Cancel the Repeat Function: Press the REPEAT BUTTON until the repeat indicator goes off. SKIP AND SEARCH MODE 1. During Play or Pause mode, tap the SKIP + or SKIP - BUTTON to go to the next track or go back to the beginning of the current track. 2. During Play mode or Pause mode, press and hold the SKIP + or SKIP - BUTTON to search within the current track with audible high speed playback. PROGRAM PLAY MODE This function allows music tracks to be played in a programmed sequence. NOTE: Program can only be set in STOP mode. 1. Press the PROGRAM BUTTON once. Both Program Number “01” and the PROGRAM INDICATOR will flash. 2. Press the SKIP + or SKIP - BUTTON to select the track to be programmed. 3. Press the PROGRAM BUTTON again to store the selection. The Program Number will advance to “02” and flash to prompt for the next input. 4. You may repeat steps #2 to #3 to program up to 20 tracks. As soon as you have entered the 20th track, the LED DISPLAY will automatically show the programmed tracks one by one in their correct sequence starting from the first. At the end of program review, Program Number “01” and the PROGRAM INDICATOR will both flash. 5. Press the PLAY BUTTON to complete and start program play. Press the STOP BUTTON to stop. 6. To review/edit the programmed tracks during play, press the STOP BUTTON and then the PROGRAM BUTTON, the LED DISPLAY will automatically show the programmed tracks one by one in their correct sequence starting from the first. At the end of program review, Program Number “01” and the PROGRAM INDICATOR will both flash. If you do not want to change any track in the program, press PLAY BUTTON. 7. To edit a programmed track, first press the PROGRAM BUTTON until you reach the program number whose track you want to change then press the SKIP+ or SKIP- BUTTON to select a new track and press PROGRAM BUTTON again to confirm. 8. To cancel program play, press the STOP BUTTON twice while reviewing programmed tracks or open the CD DOOR in STOP ...
Dieses Handbuch ist für folgende Modelle:Player - Hello Kitty KT2024A (583.24 kb)