Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
The Program Number will advance to “02” and flash to prompt for the next input. 4. You may repeat steps #2 to #3 to program up to 20 tracks. As soon as you have entered the 20th track, the LED DISPLAY will automatically show the programmed tracks one by one in their correct sequence starting from the first. At the end of program review, Program Number “01” and the PROGRAM INDICATOR will both flash. 5. Press the PLAY BUTTON to complete and start program play. Press the STOP BUTTON to stop. 6. To review/edit the programmed tracks during play, press the STOP BUTTON and then the PROGRAM BUTTON, the LED DISPLAY will automatically show the programmed tracks one by one in their correct sequence starting from the first. At the end of program review, Program Number “01” and the PROGRAM INDICATOR will both flash. If you do not want to change any track in the program, press PLAY BUTTON. 7. To edit a programmed track, first press the PROGRAM BUTTON until you reach the program number whose track you want to change then press the SKIP+ or SKIP- BUTTON to select a new track and press PROGRAM BUTTON again to confirm. 8. To cancel program play, press the STOP BUTTON twice while reviewing programmed tracks or open the CD DOOR in STOP mode. 9. To turn off the CD player, slide the FUNCTION Switch to “OFF”. The POWER Indicator will go off. AUX IN OPERATION This CD Player includes an AUX IN JACK so you can enjoy your iPod, MP3 Player or other audio device. 1. Connect the headphone jack of your external device and the AUX IN jack located on the back of this CD player. (The connection cable is not included.) 2. Turn on the CD player and it will enter the AUX function mode once the AUX IN jack is plugged. 3. Start to play your iPod, MP3 player or other audio device. 4. Slowly adjust both the volume controls on your CD player and the external device. 5. Turn off your iPod, MP3 player etc. when you finished listening. Turn the CD player off and unplug the AUX IN jack. Remark: Once the AUX IN jack is plugged, the CD player will enter the AUX mode automatically no matter the FUNCTION Switch is in CD, FM or AM mode. Remember to disconnect the connection cable from the CD player after use in order to be able to listen to CD music, FM or AM broadcasts again. CARE AND MAINTENANCE 1. Children should be supervised when using this appliance. 2. Never wrap the earphone lead around any animal or person. Special care should be taken with long wires. 3. Clean your unit with a damp (never wet) cloth. Solvent or detergent should never be used. 4. Avoid leaving your unit in direct sunlight or in hot, humid or dusty places. 5. Keep your unit away from heating appliances and sources of electrical noise such as fluorescent lamps or motors. 6. If drop-outs or interruptions occur in the music during CD play, or if the CD fails to play at all, its bottom surface may require cleaning. Before playing, wipe the disc from the center outwards with a good soft cleaning cloth. TROUBLESHOOTING GUIDE If you experience difficulties in the use of this music system please check the following or call 1-800-777- 5331 for Customer Service. Symptom Possible Cause Solution Noise or sound distorted on AM or FM broadcast - Station not tuned properly for AM or FM. - FM: FM telescopic antenna is not extended. - AM: The bar antenna is not positioned correctly - Retune the AM or FM broadcast station. - FM: Extend FM telescopic antenna. - AM: Reposition the unit until the best reception is obtained. AM or FM no sound - Unit not in “AM” or “FM” function mode. - Volume set at minimum - Slide Function Switch to “AM” or “FM” position. - Increase Volume. CD player will not play - Unit not in CD function mode. - CD is not loaded properly. - If the CD is self-compiled, the media used may not be compatible with the player. - Exhausted battery - Select CD function mode. - Load CD with label side up. - Use better quality blank media and retest. - Replace all old batteries. CD skips while playing - Disc is dirty or scratched. - Wipe CD with clean cloth or use another disc. Intermittent sound from CD player - Dirty or defective disc - Dirty pick up lens - Player is subject to excessive shock or vibration - Clean or replace the defective disc. - Use a CD lens cleaning disc to clean the lens. - Relocate the player away from shock or vibration. Sound appears distorted at high volume setting - Volume control is set to maximum. - Batteries become low - Adjust Volume Control to a lower comfortable level. - Replace all the old batteries with new ones. 90 DAY LIMITED WARRANTY AND SERVICE VALID IN THE U.S.A ONLY SPECTRA MERCHANDISING INTERNATIONAL, INC. warrants this unit to be free from defective materials or factory workmanship for a period of 90 days from the date of original customer purchase and provided the product is utilized within the U.S.A. This warranty is not assignable or transferable. Our obligation under this warranty is the repair or replacement of the defective unit or any part ther...
Dieses Handbuch ist für folgende Modelle:Player - Hello Kitty KT2024A (583.24 kb)