The front axle differential lock switch must be depressed and held in order to activate the axle differential lock. Releasing the switch disengages the axle differential lock. Use this differential lock when you are unable to drive through certain types of terrain such as sand, mud, snow, etc. WARNING Always bring the front tires to a complete stop before engaging the front axle differential lock. Failure to stop the front tires before engaging the front axle differential lock may result in dama

114101 TABLE OF CONTENTS TABLE OF CONTENTS SECTION 1 ROUGH TERRAIN FORK LIFT SAFETY SECTION 1-1 Introduction 1-3 Standards And Symbols 1-4 Safety 1-5 Training And Knowledge 1-5 Operator's Responsibilities 1-6 Management's Responsibilities 1-7 Maintenance And Repair 1-8 Operation Safety 1-9 SECTION 2 GENERAL SAFETY 2-1 General Safety Procedures 2-3 Jump Starting 2-8 Proper Load Chart Use 2-9 SECTION 3 CONTROLS AND INSTRUMENTS 3-1 Operator's Compartment 3-3 Joystick Control Functions 3-4 Joystick

Plug power tool into the power to platform GFCI outlet. To resume machine functions, move generator toggle switch to machine functions position. All functions will operate. Engine Idle Select (rpm) Select engine idle (rpm) using the symbols on the control panel. · Rabbit and foot switch symbol: foot switch activated high idle · Turtle symbol: low idle · Rabbit symbol: high idle Check Engine Light (if equipped) Light on and engine stopped: Tag the machine and remove from service. Light on and eng

Operating the machine with an improper oil level can damage engine components. Check the oil level with the engine off. 1 Check the oil dipstick. Gasoline/LPG Engine: located above the bellhousing on the bulkhead side of the engine. Diesel Engine: located on the engine block near the engine oil filter. Result: The oil level should be at the full mark on the dipstick. Add oil as needed. Ford LRG-425 EFI Engine Oil capacity (including filter) 4.5 quarts 4.3 liters Oil viscosity requirements below

Result: The machine should move in the direction that the blue arrow points on the drive chassis, then come to an abrupt stop. 48 Slowly move the drive control handle in the direction indicated by the yellow arrow on the control panel until the machine begins to move, then return the handle to the center position. Result: The machine should move in the direction that the yellow arrow points on the drive chassis, then come to an abrupt stop. Note: The drive brakes must be able to hold the machine

82750 Third Edition • Third Printing Operator's Manual SAFETY RULES Do not alter or disable the limit switches. Do not drive over 0.5 mph / 0.8 km/h with the platform raised. Do not depend on the tilt alarm as a level indicator. The tilt alarm sounds on the chassis and in the platform when the machine is on a severe slope. If the tilt alarm sounds: Lower the platform. Move the machine to a firm, level surface. If the tilt alarm sounds when the platform is raised, use extreme caution to lower the

1 Avoid hazardous situations. 2 Always perform a pre-operation inspection. 3 Always perform function tests prior to use. 4 Inspect the workplace. 5 Only use the machine as it was intended. Fundamentals The Operating Instructions section provides instructions for each aspect of machine operation. It is the operator's responsibility to follow all the safety rules and instructions in the operator's, safety and responsibilities manuals. Using the machine for anything other than lifting personnel, al

114002 Third Edition Fourth Printing Part No. 114002 Operator’s Manual Third Edition • Fourth Printing Important Read, understand and obey these safety rules and operating instructions before operating this machine. Only trained and authorized personnel shall be permitted to operate this machine. This manual should be considered a permanent part of your machine and should remain with the machine at all times. If you have any questions, call Genie Industries. Contents Page Safety Rules ..........

Battery condition will affect the ability of the machine to climb a slope. Genie Z-34/22 & Genie Z-34/22N PartNo.43654 Second Edition • Ninth Printing Operator's Manual Driving on a slope Determine the uphill, downhill and side slope ratings for the machine and determine the slope grade. Maximum slope rating, counterweight uphill (gradeability): 20% (11°) Maximum slope rating, counterweight downhill: 20% (11°) Maximum side slope rating: 20% (11°) Note: Slope rating is subject to ground condition

That means every new operator should perform a pre-operation inspection, function tests, and a workplace inspection before using the machine. Genie Z-34/22 & Genie Z-34/22N PartNo.43654 Second Edition • Ninth Printing Operator's Manual Emergency Stop Push in the red Emergency Stop button to the off position at the ground or platform controls to stop all machine functions. Repair any function that operates when the red Emergency Stop button is pushed in. Selecting and operating the ground control