Anleitung Yamaha, modell LS9-32
Hersteller: Yamaha
Dateigröße: 3.78 mb
Dateiname:
Unterrichtssprache:
|
 
|
|
|
Link zum kostenlosen Download Hinweise finden Sie am Ende der Seite
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
NONE No assignment SLOT1-1...SLOT1-16, SLOT2-1(*)...SLOT2-16(*) Input channels of an I/O card installed in a slot RACK1A, RACK1B...RACK5L(A)...RACK8R(B) L/R outputs of Rack 1–8 (*) SLOT2 can be displayed only if you’re editing offline and have selected LS9-32 in the Model Select field of the Mixer Setup window, or if you are editing online with the LS9-32 connected. DPOINT (Insert point) Selects the position at which insert-in/out will be patched. Choose from PRE EQ, PRE FADER, or POST ON. .DIRECT OUT (except for ST IN CH) 1 2 3 4 AON Turns the direct output on/off. BDIRECT OUT GAIN Adjusts the gain of the direct output. The current value is shown in the numerical box below the knob. You can set this to the nominal value (0.0 dB) by holding down the (< >) key and clicking the knob. CDIRECT OUT PORT Click this to select one of the following output ports as the one used for direct out. NONE No assignment OMINI1–OMNI16(*) OMNI jacks 1–16(*) SLOT1-1...SLOT1-16, SLOT2-1(*)...SLOT2-16(*) Output channels of an I/O card installed in a slot 2TR DOUT L, 2TR DOUT R L/R channels of the 2 TR OUT DIGITAL jack LS9 Editor Owner’s Manual 35 REC IN L, REC IN R L/R channels of the USB memory recorder input REC IN L, REC IN R L/R channels of the USB memory recorder input ) OMNI jacks 9–16 and SLOT2 can be displayed only if you’re editing offline and have selected LS9-32 in the Model Select field of the Mixer Setup window, or if you are editing online with the LS9-32 connected. DDIRECT OUT POINT Select either PRE HPF, PRE EQ, or PRE FADER as the location at which direct out will be patched. .RECALL SAFE/MUTE SAFE These enable/disable Recall Safe and Mute Safe for the channel. .MUTE GROUP AMUTE GROUP Selects the mute group (1–8) to which that channel belongs. 1 .Fader AON Switches the input channel on/off. This is linked with the INPUT section CH [ON] keys on the LS9’s panel. BFader Adjusts the input level of the input channel. This is linked with the INPUT section faders of the LS9’s panel. A meter indicating the signal level is shown at the right of the fader, and the current value is shown in the numerical box immediately below. You can set this to the minimum value (–. dB) by holding down the (< >) key of your computer keyboard and clicking the fader knob, or set it to the nominal value (0.00 dB) by holding down the (< >) key and key and clicking the fader knob. CCUE This button cue-monitors the signal of the input channel. This is linked with the INPUT section [CUE] keys on the LS9’s panel. 1 2 3 LS9 Editor Owner’s Manual 36 If a MIX channel is selected .CHANNEL SELECT (Channel selection) 1 2 .TO MATRIX 2 1 3 ASELECT (Channel selection) Except for the fact that your editing applies to a MIX channel, this is the same as the channel selection for an input channel (. p.27). BOUTPUT PATCH This selects the output port that will be assigned to the MIX channel. (For the output ports that can be selected (. p.18). If multiple patches have been made, only the first port is shown. If you change the patching in this window, the port that had been assigned until then will be cancelled, and only the newly selected port will be assigned. AMATRIX send level This adjusts the send level of the signal sent from the MIX channel to the MATRIX buses. BON (MATRIX send on/off) This is an on/off switch for the signal sent from the MIX channel to the MATRIX bus. CPOINT (Send point) Select either PRE or POST as the position from which the signal is sent from the MIX channel to the MATRIX bus. PRE POINT is selected if this is on, or POST FADER is selected if this is off. The PRE POINT setting can be made in the Mixer Setup screen. HINT • If you are using MATRIX buses in stereo, the knob for the odd-numbered bus will be PAN. • The stereo/mono status can be specified in the Mixer Setup screen. Knob of odd- numbered side LS9 Editor Owner’s Manual 37 .. Here you can specify how the signal will be sent from the MIX channel to the STEREO bus / MONO bus. MODE • ST/MONO button When this button is on, the signal will be sent to the STEREO bus and independently to the MONO bus. PAN Adjusts the panning of the signal sent from the MIX channel to the STEREO bus L/R channels. You can set this to the center position by holding down the (< >) key of the computer keyboard and clicking the knob. This is linked with the [PAN] encoder in the SELECTED CHANNEL section of the LS9 panel. If the selected MIX bus is used as a stereo bus, the odd-numbered channel is fixed at L63 and the even-numbered channel fixed at R63. ST Switches the signal sent from the MIX channel to the STEREO bus on/off. MONO Switches the signal sent from the MIX channel to the MONO bus on/off. BALANCE This is shown only if the selected MIX bus is assigned as a stereo bus. It adjusts the left/ right volume balance of the stereo bus. You can set this to the center position by holding down the (< >) key of the computer keyboard and clicking the knob. • LCR button Whe...
Dieses Handbuch ist für folgende Modelle:
Musikinstrumente - LS9-16 (3.78 mb)
)
