Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Set the DSP Mode to “FLNG 1” (slow deep flange + reverb) • Select the Overdrive channel, Gain 1. Set the DSP Mode to “CHO 1” (slow tremolo chorus + reverb) (the setting for the Clean channel is now saved to memory) • Select the Overdrive channel, Gain 2. Set the DSP Mode to “T-WAH000” (touch sensitive wah-wah) (the setting for the Overdrive channel, Gain 1 is now saved to memory) • Reselect the Clean channel (the setting for the Overdrive channel, Gain 2 is now saved to memory) Now when you go back to the Clean channel, even though the DSP Mode was last set to “T-WAH,” Channel Tracking automatically recalls the last setting for the Clean channel – in this example, “FLNG 1.” Change to the Overdrive channel, Gain 1, and “CHO 1” is recalled. Change to the Overdrive channel, Gain 2, and “T-WAH” is recalled. That’s the power of Channel Tracking! (Note: Even when the power is turned off, Channel Tracking still retains the settings – until you change them!) The Front Panel: 4 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 1: INPUT: Use this 1/4” jack to connect your guitar to the amplifier by means of a shielded instrument cable. OVERDRIVE CHANNEL: A high gain channel giving you sounds from a slight edge to serious overdrive. 2: GAIN 1: Use this control to adjust the amount of light distortion for the Overdrive channel. Gain 1 produces less intense distortion than Gain 2 (#3) and is active when the Gain switch (#5) is in the out position. 3: GAIN 2: Use this control to adjust the amount of heavy distortion for the Overdrive channel. Gain 2 produces more intense distortion than Gain 1 (#2) and is active when the Gain switch (#5) is depressed. 4: SHAPE: Use this control to “dial in” the tone for the Overdrive channel when Gain 2 is selected. Rotating the control counterclockwise enhances the mid frequencies, while rotating the control clockwise enhances the low and high frequencies. This control is active only when Gain 2 is selected. 5: GAIN SELECT: Use this switch to select which gain control is active for the Overdrive channel. With the switch in the out position, Gain 1 is selected. When the switch is depressed, Gain 2 is selected. 6: LOW: Use this control to adjust the low frequency level of the Overdrive channel. 7: HIGH: Use this control to adjust the high frequency level of the Overdrive channel. 8: LEVEL: Use this control to adjust the output level of the Overdrive channel. 9: CHANNEL SWITCH: Use this switch to select either channel. With the switch in the out position, the Clean channel is selected. When the switch is depressed, the Overdrive channel is selected. CLEAN CHANNEL: A normal gain channel designed to give you crystal clear sounds to medium distortion. 10: LEVEL: Use this control to adjust the output level of the Clean channel. 11: LOW: Use this control to adjust the low frequency level of the Clean channel. 12: MID: Use this control to adjust the midrange frequency level of the Clean channel. 13: HIGH: Use this control to adjust the high frequency level of the Clean channel. 14: DSP LEVEL: Use this control to adjust the amount of digital effect: in its fully counterclockwise position the signal will be “dry” (without any effect). As you rotate the control clockwise the amount of effect increases. 15: DSP MODE: Use this control to select one of the 16 built-in digital effects. The effects available are listed on page 3 of this manual. 16: INSERT: Use this jack to connect an external effects device to the amplifier. Use a stereo 1/4” male Y connector: ring = send, tip = return, sleeve = ground. (Refer to the illustration at the bottom of page 5.) 17: EXTERNAL SPEAKER: Use this jack to connect the amplifier to an external speaker. This jack is wired in series with the internal speaker, which remains active even when an external speaker is connected. 18: ON LED: This LED will illuminate when power is applied to the amplifier. 19: POWER: Use this switch to turn the amplifier on (top of the switch depressed) and off (bottom of the switch depressed). GFX-120T/212T Guitar Amps with DSP & Channel Tracking GFX-120T/212T Guitar Amps with DSP & Channel Tracking The Electronic Tuner: 20 20. ELECTRONIC TUNER (top panel): The electronic tuner is active whenever the amplifier is turned on, providing constant, “real-time” tuning. The bottom row of LEDs indicate which note (string) is being tuned. The top row of LEDs provides directional queues to facilitate quick and precise tuning of your instrument. The indicated note (string) is properly tuned when only the center LED is illuminated. The Rear Panel (not shown): 21: AC LINE CORD: This grounded power cord is to be plugged into a grounded power outlet, wired to current electrical codes and compatible with the voltage, power, and frequency requirements stated on the rear panel. Do not attempt to defeat the safety ground connection. 21: FUSE: The fuse protects the amplifier from damages caused by a faulty AC power source and/or other problems. If the fuse opens, ...
Dieses Handbuch ist für folgende Modelle:Musikinstrumente - GFX-120T (1.1 mb)