Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
14: DSP LEVEL: Use this control to adjust the amount of digital effect: in its fully counterclockwise position the signal will be “dry” (without any effect). As you rotate the control clockwise the amount of effect increases. 15: DSP MODE: Use this control to select one of the 16 built-in digital effects. The effects available are listed on page 3 of this manual. 16: INSERT: Use this jack to connect an external effects device to the amplifier. Use a stereo 1/4” male Y connector: ring = send, tip = return, sleeve = ground. (Refer to the illustration at the bottom of page 5.) 17: EXTERNAL SPEAKER: Use this jack to connect the amplifier to an external speaker. This jack is wired in series with the internal speaker, which remains active even when an external speaker is connected. 18: ON LED: This LED will illuminate when power is applied to the amplifier. 19: POWER: Use this switch to turn the amplifier on (top of the switch depressed) and off (bottom of the switch depressed). GFX-120T/212T Guitar Amps with DSP & Channel Tracking GFX-120T/212T Guitar Amps with DSP & Channel Tracking The Electronic Tuner: 20 20. ELECTRONIC TUNER (top panel): The electronic tuner is active whenever the amplifier is turned on, providing constant, “real-time” tuning. The bottom row of LEDs indicate which note (string) is being tuned. The top row of LEDs provides directional queues to facilitate quick and precise tuning of your instrument. The indicated note (string) is properly tuned when only the center LED is illuminated. The Rear Panel (not shown): 21: AC LINE CORD: This grounded power cord is to be plugged into a grounded power outlet, wired to current electrical codes and compatible with the voltage, power, and frequency requirements stated on the rear panel. Do not attempt to defeat the safety ground connection. 21: FUSE: The fuse protects the amplifier from damages caused by a faulty AC power source and/or other problems. If the fuse opens, replace it ONLY with the same size and type. If fuses continue to fail, check the AC source – if the source is okay, contact your Crate dealer for service information. 22: CHANNEL SELECT / GAIN FOOTSWITCH JACK: Use this jack to connect the stereo 1/4” plug of the supplied three-button footswitch for remote control of channel selection and gain selection. 23: REVERB FOOTSWITCH JACK: Use this jack to connect the mono 1/4” plug of the supplied three- button footswitch for remote control of DSP on and off. CONNECTING TO THE INSERT JACK: The Insert jack (#16) allows you to patch an external effects device into the amplifier prior to its power amp stage. Use Crate’s STP201, STP202 or STP203 stereo-to-mono Y cord or an adapter such as Crate’s YPP117 and two 1/4” mono signal cables to connect the effect as shown to the immediate right. Stereo-to-mono Y-cord: Y-adapter and 2 cables: RETURN SEND GROUND TIP RING SLEEVE to Insert jack (STP201, 3' STP202, 6' STP203, 9') to effect "OUT" jack to effect "IN" jack RINGTIP to Insert jack (YPP117) (1/4"-TO-1/4" MONO SHIELDED CABLES) TIP RING SLEEVE RINGTIP External Effect to to effect effect "OUT" "IN" jack jack External Effect GFX-120T/212T Guitar Amps with DSP & Channel Tracking Suggested Settings: GFX-120T/212T Guitar Amps with DSP & Channel Tracking System Block Diagram: TUNER INPUT CHANNEL SELECT FLEX WAVE STAGE LOWLEVEL MID HIGH LOW SHAPE HIGH LEVEL LEVEL MODE GAIN GAIN SHAPE ACTIVE BUFFER MIX AMP INSERT CLEAN CHANNEL DSP OVERDRIVE CHANNEL DAMPING CIRCUIT POWER AMP SPEAKER EQ A BC D EF G SPEAKER EXT. GFX-120T/212T Guitar Amps with DSP & Channel Tracking GFX-120/212T TECHNICAL SPECIFICATIONS: Output Power Rating 120W RMS @ 5% THD, 4., 120 VAC Speaker Size and Rating GFX-120T (1) Custom Design 12”, 4. GFX-212T (2) Custom Design 12”, 8. Input Impedance 470k. Total System Gain Overdrive Ch Gain 1: 88dB, all controls @10; Gain 2: 110dB Clean Ch 58dB, all controls @10 Maximum Input Signal Accepted 7 volts peak-to-peak Overdrive Channel Low Control 11dB range @ 80Hz Shape Control Proprietary Circuit High Control 10dB range @10kHz Clean Channel Low Control 22dB range @ 80Hz Mid Control 14dB range @ 600Hz High Control 28dB range @ 10kHz Power Requirements 120 VAC, 60Hz, 95VA; 100/115VAC, 50/60Hz, 95VA; 100/115VAC, 50/60Hz, 95VA Size and Weight GFX-120T 17-1/2” H x 19-1/4” W x 9-3/4” D, 44 lbs. GFX-212T 21” H x 26-1/2” W x 11” D, 50 lbs. The GFX-120T/212T is covered with a durable charcoal gray Tolex material: wipe it clean with a lint-free cloth. Never spray cleaning agents onto the cabinet. Avoid abrasive cleansers which would damage the finish. Crate continually develops new products, as well as improves existing ones. For this reason, the specifications and information in this manual are subject to change without notice. Declaration Of Conformity #34, Effective 01-01-2001 Manufacturer’s Name: SLM Electronics Production Facility: 11880 Borman Drive, St. Louis, MO 63146, USA Production Facility: 700 Hwy 202 W, Yellville, AR 72687, USA Shipping Facility: 1400 ...
Dieses Handbuch ist für folgende Modelle:Musikinstrumente - GFX-212T (1.1 mb)