Stimmen - 4, Durchschnittliche Bewertung: 3.3
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
1 Prepare the sound source. away from fluorescent lights. following cases. for an extended period of time. When unplugging the .iPod classic 120 GB, 160 GB (2009) mode automatically in about 30 minutes when there is no To select a memory on the USB device Connect additional audio component to the AUDIO Press ./.. repeatedly to select “PLAY SET?,” then .Point the remote at the system’s sensor. .There are many folders or files on the USB device. operation or audio signal output. unit, always grip the plug. Never pull the cord itself. .iPod classic 160 GB (2007) .iPod classic 80 GB .. If the USB device has more than one memory (for press .Should any solid object or liquid get into the system, .Move the remote closer to the system. . The file structure is extremely complex. By default, the automatic standby function is turned on. .iPod nano 5th generation (video camera) example, internal memory and a memory card), you can (not supplied). 4 Set the time to start playback. .The memory capacity is excessive. Use buttons on the unit to turn off the automatic standby unplug the system, and have it checked by qualified .iPod nano 4th generation (video) select which memory to use and then start playback. IN jack . on the unit using an audio analog cord The STANDBY indicator . remains lit after personnel before operating it again. .iPod nano 3rd generation (video) function. You cannot select a memory during playback. Make sure .The internal memory is fragmented. 2 Turn down the volume. Press ./.. repeatedly to set the hour, then press .iPod nano 2nd generation (aluminum) unplugging the power cord. .The AC power cord can be changed only by a qualified .. Use the procedure above to set the minutes. Hold down .... while the system is on, until .iPod nano 1st generation to select a memory before starting playback. Press VOLUME ... .The STANDBY indicator . may not turn off Erroneous display service facility. “AUTO STBY OFF” appears. .iPod 5th generation (video) Use buttons on the unit to select a memory on the USB 3 Select the AUDIO IN function. 5 Use the same procedure as in step 4 to set the time immediately after unplugging the power cord. The .Send the music data to the USB device again, as the .iPod 4th generation (color display) device. to stop playback. indicator will turn off after about 40 seconds. This is not To turn on the function, repeat the procedure until On placement .iPod 4th generation data stored in the USB device may have been corrupted. Press FUNCTION +/.. repeatedly. a malfunction. “AUTO STBY ON” appears. .Do not place the system in an inclined position or in . iPod mini 1 Press FUNCTION . repeatedly to select the USB 6 Select the sound source. .The character codes that can be displayed by this . iPhone function. Press ./.. repeatedly until the desired sound system are numbers and alphabets only. Other Notes . iPhone 3G 4 Start playback. locations that are extremely hot, cold, dusty, dirty, or humid or lacking adequate ventilation, or subject to Start playback of the connected component and adjust .. CD/MP3 player characters are not displayed correctly. . “AUTO STBY” appears in the display for 2 minutes before the . iPhone 3GS source appears, then press vibration, direct sunlight or a bright light. 2 Connect the USB device to the (USB) port .. system enters standby mode. the volume. USB section (except for North American model) 7 Turn off the system. . The automatic standby function is invalid for the tuner function .Be careful when placing the unit or speakers on The sound skips, or the disc will not play. The USB device is not recognized. Supported bit rate: 3 Press TOOL MENU ., and then press ENTER .. Note (FM/DAB), even when you have enabled it. surfaces that have been specially treated (for example, MP3 (MPEG 1 Audio Layer-3): 32 kbps . 320 kbps, VBR The system may enter standby mode automatically if the volume Press ..... The system automatically turns on .Wipe the disc clean, and replace it. .Turn off the system and reconnect the USB device, then . The system may not enter standby mode automatically in the WMA: 48 kbps . 192 kbps, VBR 4 Press ./.. repeatedly to select a memory with wax, oil, polish) as staining or discoloration of the level of the connected component is too low. Adjust the component’s before the preset time. .Move the system to a location away from vibration (for turn on the system. following cases; AAC: 48 kbps . 320 kbps number. volume accordingly. See “To turn off the automatic standby function.” surface may result. Sampling frequencies: If the system is on at the preset time, the Play Timer example, on top of a stable stand). .Check the information on the websites about .while an audio signal is being detected. .If the system is brought directly from a cold to a warm MP3 (MPEG 1 Audio Layer-3): 32/44.1/48 kHz Proceed to step 5 if only one memory can be selected. will not play. Do not operate the system from the time .Move the speakers away from the system, or place them comp...
Dieses Handbuch ist für folgende Modelle:Stereoanlage - CMT-MX550I (862.71 kb)