Stimmen - 3, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
For Daewoo technical support call 1-800-245-9870.) Model : 531X DAEWOO ELECTRONICS CO., LTD. http : //svc.dwe.co.kr September, 2000 CONTENTS SAFETY PRECAUTIONS GENERAL SAFETY INFORMATION SERVICING PRECAUTIONS TECHNICAL INFORMATION GENERAL INFORMATION PIN CONNECTOR CAUTIONS FOR ADJUSTMENT AND REPAIR OPERATION AND ADJUSTMENT 9 ALIGNMENT PROCEDURE 12 TROUBLESHOOTING HINTS 15 BLOCK DIAGRAM 29 PCB LAYOUT 30 SCHEMATIC DIAGRAM 33 EXPLODED VIEW DIAGRAM 37 INFORMATION OF PART DESCRIPTION 38 ELECTRICAL PARTS LIST 39 SAFETY PRECAUTIONS CAUTION: No modifications of any circuits should be attempted. Service work should be performed only after you are thoroughly familiar with all of the following safety checks and servicing guidelines. Safety Check Care should be taken while servicing this analog color display because of the high voltages used in the deflection circuits. These voltages are exposed in such areas as the associated flyback and yoke circuits. Fire & Shock Hazard • Insert an isolation transformer between the analog color display and AC power line before servicing the chassis. • When servicing, pay close attention to the original lead dress especially in the high voltage circuit area; if a short circuit is found, replace all parts which have been overheated as a result of the short circuit. • All the protective devices must be reinstalled per original design. • Soldering must be inspected for possible cold solder points, frayed leads, damaged insulation, solder splashes or sharp solder points. Be certain to remove all foreign materials. Implosion Protection Picture tube in this monitor employs integral implosion protection system, but care should be taken to avoid damage and scratching during installation. Only use same type replacement picture tubes. IMPORTANT SAFETY NOTICE: There are special components used in this analog color display, which are important for safety. These parts are shaded on the schematic diagram and on the replacement parts list. It is essential that these critical parts should be replaced with manufacturer’s specified parts to prevent X-Ray, shock, fire or other hazards. Do not modify the original design without getting written permission from DAEWOO ELECTRONICS CO. or this will void the original parts and labor warranty. X-Ray WARNING: The only potential source of X-Ray is the picture tube. However when the high voltage circuitry is operating properly, there is no possibility of an X-Ray problem. The basic precaution which must be exercised is to keep the high voltage at the following factory recommended level. NOTE: It is important to use an accurate, periodically, calibrated high voltage meter. • To measure the high voltage, use a high-impedance high-voltage meter. Connect(-) to chassis and (+) to the CRT anode button. • Turn the Contrast & Brightness Control fully counterclockwise. • Measure the high voltage. The high voltage meter should indicate the following factory recommended levels. • If the upper meter indication exceeds the maximum level, immediate service is required to prevent the possibility of premature component failure. • To prevent X-Ray possibility, it is essential to use the specified picture tube. • The normal high voltage is 25.5KV or below and must not exceed 29KV at zero beam current at rated voltage. 1 GENERAL SAFETY INFORMATION Terms in the manual CAUTION Statements identify conditions or practices that could result in damage to the equipment or other property. WARNING Statements identify conditions or practices that could result in personal injury or loss of life. . Terms as marked on equipment CAUTION Statements indicate a personal injury hazard not immediately accessible as one reads the marking or a hazard which is properly included on the equipment itself. WARNING Statements are clearly concerning indicated personal injury hazards. . Symbols in the manual The symbols indicate where applicable cautionary or other information is to be found. . Symbols as marked on equipment Protective GROUND terminal . High Voltage Warning And Critical Component Warning Label The following warning label is on the CRT PWB shield case inside the unit. Warning: This product includes critical mechanical and electrical parts which are essential for x ray protection. For continued safety, replace critical components that are indicated in the service manual with exact replacement parts given in the parts list. Operating high voltage with this product is 29Kv at minimum brightness. Refer to service manual for measurement procedures and proper service adjustments. 2 SERVICING PRECAUTIONS CAUTION: Before servicing instruments covered by this service manual, its supplements, and addendum, please read and follow the SAFETY PRECAUTIONS of this manual. NOTE: If unforeseen circumstances create conflict between the following servicing precautions and any of the safety precautions on page 1 of this manual, always follow the safety precautions. Remember: Safety First. General Servicing ...