DC888 PARTS LIST KEY UTY OF SCRIPTION KF r QT y C( ■ÍH f’ílDM KF Y QT Y □ FSCKIPriON 1 5 GLIDE , 7 9 M9x014x2Or«n 12 1 BACKREST POST ♦ 2 1 BASE MACHINE SCREW Pt>STtC COVER 3 1 BASE COVSR S 1 KN08 FOR IN & OUT 13 i PUSTIC HOLOER 4 1 SEAT POST 9 1 FIAT WASHER 14 1 STEEL PUVTE 5 1 SEAT 10 1 LOCK WASHER Í 15 2 BACKREST SCREW 5 1 MECHANISM 11 1 BACKfEST ! 1« 1 PLASTIC COVER STEP 1. > Insert (1) glides Into (2) base Place (3) base cover on (2) base. Insert (4) sett post Into (2) base. S

DC410 PART LIST KEY QTY DESCRIPTION 1 5 Casters or Clides 2 1 Base 3 1 Gas Cylinder 4 1 Cylider Cover 5 1 Seat Plate 6 1 Seat 7 1 Backrest + Plastic Cover 8 1 Connector Cover 9 1 Backrest Height Adjuslment Knob 10 1 Backrest Stopper 11 6 Seat Plate Screws 12 1 Footrest 13 1 Knob For Footrest PREVENTIVE MAINTENANCE AND WARNING! • USE THIS PRODUCT ONLY FOR SEATING ONE PERSON AT A TIME. • DO NOT USE THIS CHAIR AS A STEP STOOL / LADDER. • DO NOT USE CHAIR UNLESS ALL BOLTS . SCREWS

Note that the back tube extension of the lower leg frame is longer than the front 3. Align holes in upper and lower frames at desired height' insert height adjustment rod "K", and secure with adjustment knob. Repeat for left and right frames. IMPORTANT:It is best to set the proper height at this time. Use chart below as a guideline to determine height adjustment positions. HEIGHT ADJUSTMENT GUIDELINES Page 3 I ■ If 111111111111111111111111111 * 11111111 j11111111 0" I" 2" 3" 4. Attach back

If attaching metal pencil ledge, folded-over edge should be on the underside ( unfinished side ) of tabletop and should point towards back edge of board. Figure 5 Pencil Tray Figure 6 Pencil Ledge Page 7 I ■ If 111111111111111111111111111‘11111111111111111 0" I" 2" 3" 15. Carefully turn base assembly upside down and place on table top (this may require two people ) Be sure that the two threaded inserts near the back edge of the table top align with the attachment holes in the tilt mechan

( Middle piece has open top and open bottom. Bottom piece has open top and solid bottom with 4 round feet. Top piece has solid smooth top and open bottom.) TIP: When snapping together, start simultaneously in the two front corners and slowly work your way to the back corners making sure that each tab is aligned before applying pressure. When complete, slightly loosen the alien bolts holding the drawer support hangers "H" and slide each of the drawer units into place. Retighten all drawer support

Use care to differentiate rear crossbar (B) (341/2" long) from footrest crossbar (C) (351/2" long). Attach the rear crossbar (B) and footrest crossbar (C) to one side frame (A) using 2" Allen bolts (H). Tighten securely. Note: Threaded barrels preattached to leg frames must be in rear and facing out. Attach other side frame (A) to opposite ends of crossbars in step two using 2" Allen bolts (H). Tighten securely. Place dust cover (D) over top of base frame and attach using %" Phillips screws (

Position adjustment knobs facing out and tighten lower screws using a Phillips screwdriver. Figure 1 Figure 2 Rear extension tube Front extension tube Insert front and rear extension tubes, (B) and (C), into base frame as shown in figure 1. For the time being, set each tube at a height of approximately 4" and lock into place by tightening adjustment knob. (see figure 2). Adjustment knob Lower Phillips screw Place your drawing board/tabletop on a soft pad or carpet to avoid scratches wit