Stimmen - 2, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
Prior to installing the slicer, test the electrical service to assure it agrees with the specifications on the machine data plate. The data plate is located on the right side of the slicer base. CARRIAGE TRAY The Carriage Tray is secured to the slicer when the knob on the Carriage Tray / Support Arm is turned clockwise until snug (Fig. 1). Refer to page 14 for assembly information. SHARPENER The Sharpener should already be mounted on top of the slicer and locked to its bracket (Fig. 1). TOP KNIFE COVER The Top Knife Cover should already be in place and secured with its Latch Knob (Fig. 2). DEFLECTOR The Deflector should already be mounted below the knife (Fig. 1). FENCE Either Fence (Fig. 1) can be clamped on the Carriage Tray to limit product movement during slicing. Model 2812 Shown 1. Back out Thumb Screw.Lay Fence on CarriageTray. 2. Rotate to Vertical. 3.Slide Fence Up. Tighten Screw. Fig. 1 ELECTRICAL WARNING: THIS MACHINE IS PROVIDED WITH A THREE-PRONG GROUNDING PLUG. THE OUTLET TO WHICH THIS PLUG IS CONNECTED MUST BE PROPERLY GROUNDED. IF THE RECEPTACLE IS NOT THE PROPER GROUNDING TYPE, CONTACT AN ELECTRICIAN. CLEAN BEFORE USING The 2812, 2812PS and 2912 slicer must be thoroughly cleaned and sanitized after installation and before being used. Refer to Cleaning, page 13. – 4 – OPERATION SAFETY SAFETY DEVICES INCORPORATED IN THIS SLICER MUST BE IN THEIR CORRECT OPERATING POSITIONS ANYTIME THE SLICER IS IN USE. The TOP KNIFE COVER must be in position and secured with the LATCH KNOB (Fig. 2). The RING GUARD is not removable. The DEFLECTOR, mounted below the slicer knife, can be removed for cleaning. The MEAT GRIP (Fig. 2) must be used when slicing to keep your hand(s) away from the knife. When the slicer is not running, the INDEX KNOB (Fig. 2) must be turned back below zero (fully clockwise). The GAUGE PLATE will then cover the knife edge. Always UNPLUG the POWER CORD before cleaning or moving the Slicer. Model 2812 Shown Fig. 2 WARNING: ROTATING KNIFE. USE MEAT GRIP. UNPLUG MACHINE POWER CORD BEFORE CLEANING, SERVICING, OR REMOVING PARTS. REPLACE PARTS BEFORE USE. SLICING — MODEL 2812 & 2812PS With the Gauge Plate fully closed, pull the Carriage all the way toward you until it reaches its stop. With the Meat Grip out of the way, place the product to be sliced on the Carriage Tray. Set the Meat Grip against the product. If the Meat Grip is not needed, it may be stored out of the way by rotating it behind the top of the Carriage Tray where it can rest on the Retaining Clip (Fig. 2). With the Gauge Plate in the closed position, turn the slicer on by pulling the Switch Knob (Fig. 2). Open the Gauge Plate to obtain the desired slice thickness by turning the Index Knob (Fig. 2) and begin slicing. The numbers on the Index Knob do not indicate actual measurements but may be used for reference to duplicate slice thickness. Unless the Gauge Plate is opened and movement introduced to the Carriage within the 10 second auto shutoff period, the machine will turn off. Use the Carriage Tray Handle (Fig. 2) to push the Carriage back and forth to slice. Turn the slicer off by pushing the Switch Knob or by closing the Gauge Plate. – 5 – KEYS (2812PS ONLY) BEEP The four Preset keys (1 – 4) recall the last-entered portion mode and value and display the preset indicator (P1, P2, P3, or P4). In WEIGHT mode, the slicer beeps when the preset weight is on the platter. In SLICE mode, the slicer beeps when the preset number of slices has counted down to 0. The Memory key uses the current entry (platter weight, slice count, or numeric entry) as the portion mode and value and displays the M indicator. In WEIGHT mode, the slicer beeps when the preset weight is on the platter. In SLICE mode, the slicer beeps when the preset number of slices has counted down to 0. The Recall key momentarily displays the current portion value (P1, P2, P3, P4, or M). The Tare key (in weight mode) uses the platter weight as the Tare or accepts a numeric entry as the known Tare value. NET indicates that Tare is invoked. Repeat Tare, , to reset the platter to zero weight if slicing more than one item. To toggle Tare off, press the key. The Rezero key resets the scale to zero weight if accumulations occur up to 0.11 lb. The scale will not rezero more than 0.11 lb. While the scale is zeroing, – 0 – displays. The Mode key shifts between WEIGHT mode (either lb or oz) and SLICE mode. The CE key clears the user entry and restores the previous preset value. It turns Tare off if in NET weight mode; or, it resets the counter in SLICE mode. When the portion weight or slice count is achieved, a beep sounds. A longer beep indicates the key is not valid. A triple beep indicates the entry exceeds acceptable limits. A continuous beep indicates error. – 6 – POWER UP When the slicer is plugged in, the control checks its own circuitry, goes through a series of illuminated displays, and ends with the scale at zero in weight mode. lb P1 NET slice P2 —> 0 <— 88000 oz P3 M P4 ....