Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
2. The only thing you will need to assemble your cleaner is Assembly a Phillips head screwdriver. 1. Slide upper body into lower body. 2. Secure with screws. 3. 3. Slide handle assembly down into upper body until it will go no further. Align screw slots. 4. Secure with screw. 5. Place solution tank on back of unit. Product features 4. Solution Tank: Holds 1/2-gallon of cleaning solution. Collection Tank: Holds 1/2-gallon of dirty water. Power Cord: For storage, wrap power cord around upper and lower cord 5. wraps, and secure plug to cord with molded clip. 5 800.237.7691 ug120-4071_1770_908.indd 5 10/14/08 1:06:04 PM Operation Before you clean 1. Plan activities to give carpet time to dry. 2. Remove easily moved furniture (chairs, lamps, coffee/cocktail tables, etc.) from room if needed. 3. Vacuum carpet thoroughly. 4. Decide where to begin — and end — your job. Clean in 3’ X 4’ sections, starting in areas farthest from exit. Plan to leave a path open to empty soiled water and refill cleaner. 5. Carpeting will dry in three to four hours, depending on carpet style and air circulation in room. A floor fan speeds drying. 6. Replace furniture on damp carpeting by placing waxed paper under legs until floor dries completely. Fill the tank 1. Remove the solution tank by lifting it straight up, then away from the lower body. 2. Unscrew the black cap at the bottom of the solution tank. 3a. Add one of the BISSELL advanced cleaning formulas for deep cleaning machines to the formula fill line on the solution tank. Fill the rest of the tank with hot (not boiling) tap water to the water fill line. Replace and tighten the black cap. 3b. If using the BISSELL 3X Concentrated Fiber Cleansing Formula: Add 1/2 capful of 3X Concentrated Fiber Cleansing formula to clean water/solution tank, and then fill with hot water to the line. 4. Place solution tank on lower body. 5. Rotate Quick Release Cord Wrap™ to release the Power cord and plug into an outlet. Pre-Treating Pre-treat stubborn stains and highly soiled carpet in hallways and other high-traffic areas. 1. Using BISSELL Tough Stain pre-cleaner, generously spray evenly over soiled area, do not overwet carpet. 2. Wait 3 -5 minutes before deep cleaning. only BISSELL advanced cleaning formulas for deep cleaning machines. Use of cleaning formulas that contain lemon or pine oil may damage this appliance and void warranty. Chemical spot cleaners or solvent-based soil removers should not be used. These products may react with the plastic materials used in your QuickSteamer, causing cracking or pitting. WARNING: To reduce the risk of fire, use Tip: Always vacuum thoroughly before you deep clean. If possible, move large furniture to an area you will not be cleaning. 2. Tip: Deep cleaning spots, spills and high traffic areas on a regular basis can prolong carpet life. 6 800.237.7691 ug120-4071_1770_908.indd 6 10/14/08 1:06:04 PM With foot, press the detent lever on right side of lower body. Carpet cleaning 1. With your foot, press the red power switch [located in foot of unit] ON. 2. Operation 3. Depress spray trigger to spray cleaning solution. Do not overwet. 4. To suction up water, repeat motion over same area without pressing trigger. 5. Repeat steps 3 and 4 until no more dirt can be removed. 6. Continue to clean entire carpet, working in 3’ x 4’ sections. 7. Empty the collection tank when dirty water reaches the full line, or when the solution tank is empty. See page 8 for instructions. 8. If floor nozzle stops spraying, turn power switch OFF and check water and cleaning solution levels. Refill if needed. a. 1. Turn power switch OFF. 2. Unplug power cord from outlet. 3. Remove and empty collection tank. a. Release collection tank latches [1 each side] by pulling up from bottom of latch and then out. b. Carefully remove collection tank from lower body by lifting handle. To empty the collection tank c. e. c. Carry collection tank to a toilet or sink. To empty, pour out contents using opening at back of tank. d. Rinse collection tank thoroughly. e. Remove lint and hair from red gasket in base of unit. (Do not remove gasket) Dirty 4. Clean nozzle window by lifting latch and removing from machine. Rinse under running water. When finished replace nozzle and secure with latch. 4. 5. Replace collection tank on lower body and secure with latches. Hard floor cleaning 1. Attach hard floor tool to unit. 2. Remove the collection tank (refer to steps 3a and b in the Maintenance and care section on page 8) A. For 1770/1970 series it is necessary to remove the cross action brush first. Using your thumbs squeeze the 2 grey tabs towards the outside of the unit. Push down at the same time and release the cross action brush. Tip: It is recommended that every time your solution tank needs refilling, that you empty the contents of the collection tank. If the collection tank gets too full, you may begin to see foam spitting out of the vent cover. If this ha...