To CANCEL: Press the SLEEP button once more. The mode is set back to the previous operating mode. SLEEP MODE • Decreases the fan speed of Indoor Unit(s) automatically and quiet operation is carried out. • When Sleep mode starts to operate, desired temperature will change automatically (see below). Heat* 3°C(6°F) down an hour after 4°C(8°F) down another 3-hours after Cool & Dry 1°C(2°F) goes up an hour after • When sleep mode starts to operate, flaps will move up or down by one-step automatically

button to adjust OFF TIMER to PM 6:30 • Operation Temperature Range: HYUNDAI OPERATING RANGES Mode Temperature (°F) Indoor Humidity Indoor Outdoor Cool 70-90 70-109 <80% Dry 59-90 59-109 <80% Heat 59-81 32-75 <80% • If you operate the unit(s) at other than the above conditions, a safety device may be activated and shut off the power. • On humid days, frost may form on the surface of air conditioner or condensation may occur. HIGH POWER MODE Convenient on a hot day. (During AUTO, HEAT, COOL or DR

(See Fig. 1) 3. Make a 2 9/16” hole through the wall. Hole should be angled down to the exterior. (See Fig. 2) 4. Use a city grade wall pipe (outer diameter : 2 3/8”) as a Fig. 1 18/24 Btuh 9/12 Btuh 3.43”4.21” 1.18” 5.53” 9.12”10.83” 2’ 6” 2’ 2.25” 5.28” 6.89” 6.89” 5.79” 1.38” .85” 12.60” sleeve to protect the interconnection cable and the pip ing. (See Fig. 2) Fig. 2 Fig. 3 Wall pipe ( field supplied OD: 2 3/8”) Wall-Hook Plate Mounting Approximately 3/16”– 3/8” Indoor Outdoor Fig. 2 Pipe hol

BarFlare nut Fix pipe turning clamp handle. Pipe INSTALLING OF THE OUTDOOR UNIT Cut pipe by rotating the pipe cutter Pipe Turn the handle Clockwise while pushing it against the pipe Pipe cutter knife Yoke Do not damage the inside of the pipe. BarFlare nut Fix pipe turning clamp handle. Pipe • See the “Determination of Installing Position”. Connecting of Tubing 1. Cutting and flaring of tubing: A. Cut the tubing on its straight part with the pipe cutter. B. Remove burrs from cut edges of pipes, w

2. Set current time by pressing button. NOTE: If current time is not set correctly, the timer will not operate normally. INSTALLING REMOTE CONTROL HOLDER(S) 2 Push 1 Place • Place the bottom of the Remote Control on the hook first and then push it into the holder. NOTE: The transmitting distance may be shorter in a place where the room has electronic lighting equipment. ! CAUTION ! • If the batteries are not in use for a prolonged period of time, remove them from the battery compartment to avoid

Recommended at humid weather such as rainy days, etc. When outside temperature is too low or room size is too small, the room temperature may go down further than the set point. • When the room temperature is below 59° F , the operation is stopped and the unit is switched to the Wait Mode at which time the room temperature is monitored. MANUAL OPERATION • In case you are not satisfied with various conditions of automatic operation, you can select these conditions as you wish. • Select HEAT, DRY,

Press the SET TEMP button. AUTO OPERATION • Air-Conditioner(s) automatically selects the proper room temperature. 1. Press the MODE button on the Remote Control, and select AUTO ( )mode. 2. Press the ON/OFF button. STOP Press the ON/OFF button again. • Auto Mode controls every function of the air conditioner in order for you to feel as comfortable as possible. • The operation is automatically controlled according to the room temperature and humidity. (When you turn on the unit again within 2 hou

(22.72”) 9/12 Btuh (23.94”) 18/24 Btuh (8.86”) 9 Btuh( 11.02”) 12 Btuh(14.25”) 18/24 Btuh Distance between the unit(s) and ceiling should be more than 2” Clearance in front of unit(s) should be no less than 10’ Distance between the unit(s) and the wall should be more than 6” Fasten the unit(s) on the lower hook of wall plate Fasten the unit(s) on the upper hook of wall plate Distance between the unit(s) and the wall should be more than 6” Wall plate Patch Outgoing tubing (bottom) Wall cap Connec

supply to the condenser. ! CAUTION ! Make sure wire connections are secure otherwise electrical malfunction may occur. TEST RUN TEST RUN • After the test, set the lever to ON (I) position. The unit will stop the operation and hereafter the remote control will • Check the installation again. control the unit. • First, set the lever to OFF(O) position, then to ON(I) and TEST position slowly. (During the test, the indicator light will blink) 9/12 Btuh 18/24 Btuh CABLE CONNECTION 9/12 Btuh (Single o

• After the season, set the Hand Switch Lever to OFF (O) position. Hand Switch Lever • The Remote Control is stored inside the product. Please open the front grill to remove the Remote. Remote Control Storage Air Intake (Left side, Rear) Drain Hose Air Outlet Interconnection cable, pipes and power supply Air Outlet Drain Hose Air Intake (Left side, Rear) Interconnection cable, pipes and power supply COMPONENTS AND FUNCTIONS For the proper use, please check and identify the name and location of e