Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
To disconnect the power cord from the adapter, use one hand on each to avoid damaging the ground terminal. Avoid frequently unplugging the power cord as this can lead to eventual ground terminal damage. • Never use the appliance with a broken adapter. Temporary Use of an Extension Cord We strongly discourage the use of an extension cord due to potential safety hazards. This appliance should be installed in accordance with national wiring regulations. This guide acts as a guide to help to explain product features. Symbols used in this Manual NOTE This symbol alerts you to the risk of electric shock. This symbol alerts you to hazards that may cause harm to the air conditioner. This symbol indicates special notes. 6 Room Air Conditioner Owner's Manual 7 Here is a brief introduction of the indoor and outdoor units. Please see the information specific to your indoor unit type. Product Introduction Product Introduction Signal Receptor Front Panel Air Discharge Air Intake Vents Air Outlet Vents Power Cord Connecting Wires Piping Drain Hose Base Plate Air Filter Plasma Filter Indoor Units ENGLISH Outdoor Unit Operating Instructions Operating Instructions How to insert the Batteries 1. Remove the battery cover by pulling it according to the arrow direction. 2. Insert new batteries making sure that the (+) and (-) of battery are installed correctly. 3. Reattach the cover by sliding it back into position. 1. Always use/replace both batteries of same type. 2. If the system is not to be used for a long time, remove the batteries to save their working life. 3. If the display screen of remote controller starts, fading replace both of the batteries. NOTE 4. Use 2 AAA(1.5volt) batteries. Wireless Remote Controller Maintenance 1. Choose a suitable place where its safe & easy to reach. 2. Fix the holder to wall etc with the supplied screws firmly. 3. Slide the remote controller inside the holder. 1. Remote controller should never be exposed to direct sunlight. NOTE 2. Signal transmitter & receiver should always be clean for proper communication. Use a soft cloth to clean them. 3. In case some other appliances also get operated with remote control, change their position or consult your serviceman. 1. The signal receiver is inside the unit. 2. Aim the remote controller towards the unit to operate it. There should not be any blockage in between. Operating Method Operation Indication Lamps On/Off : Lights up during the system operation, error code and auto restart setting. * Hot start operation: Stops the indoor fan in heating operation for minutes to prevent cold air from blowing out from unit. * In defrost mode unit stops heating operation for few minutes to remove formation of ice on the heat exchanger coils to maintain the efficiency. 8 Room Air Conditioner Operating Instructions Wireless Remote Controller 1. START/STOP BUTTON ENGLISH The controls will look like the following. Signal transmitter ON OFF CANCEL AUTO CLEAN SET 1 3 5 4 9 18 10 12 14 16 7 2 8 13 15 11 6 Flip-up door (opened) 17 19 Cooling Operation Auto Operation or Auto Changeover Healthy Dehumidification Operation Heating Operation • Cooling Model( ), Heat Pump Model( ) Operation Mode Used to turn off/on the unit. 2. OPERATION MODE SELECTION BUTTON Used to select the operation mode. 3. ROOM TEMPERATURE SETTING BUTTONS Used to select the room temperature. 4. INDOOR FAN SPEED SELECTOR BUTTON Used to select fan speed in four steps low, medium, high and CHAOS. 5. JET COOL BUTTON Used to start or stop the speed cooling, heating. (It operates fan in super high speed in cooling mode, heating mode) 6. CHAOS SWING BUTTON Used to stop or start louver movement and set the desired up/down airflow direction. 7. ON/OFF TIMER BUTTONS Used to set the time of starting and stopping operation. 8. TIME SETTING BUTTONS Used to adjust the time. 9. TIMER SET/CANCEL BUTTON Used to set and to cancel the timer operation. 10. SLEEP MODE AUTO BUTTON Used to set sleep mode auto operation. 11. AIR CIRCULATION BUTTON Used to circulate the room air without cooling or heating. ENERGY-SAVING COOLING MODE BUTTON (OPTIONAL) For inverter type models ( ) 12. ROOM TEMPERATURE CHECKING BUTTON Used to check the room temperature. 13. PLASMA BUTTON(OPTIONAL) Used to start or stop the plasma-purification function. 14. HORIZONTAL AIRFLOW DIRECTION CONTROL BUTTON (OPTIONAL) Used to set the desired horizontal airflow direction. 15. RESET BUTTON Used prior to resetting time. 16. 2nd F BUTTON Used prior to using modes printed in blue at the bottom of buttons. 17. AUTO CLEAN BUTTON(OPTIONAL) Used to set auto clean mode. In some models this button has a 2nd function of LED luminosity control. 18. HEATER BUTTON(OPTIONAL) (Not available in all models) 19. LCD LUMINOSITY BUTTON(OPTIONAL) Used to adjust LCD luminosity. NOTE To use the functions printed in blue at the bottom of the buttons press 2nd F button first and then the required function button. Pressing the 2nd F button activates the blue printed function of ...
Dieses Handbuch ist für folgende Modelle:Splitgeräte - A12LH1 (886.21 kb)